REAR AXLE

EPC / Mercedes / Truck / HA / HA 745.608 / 35 / 001
‹ ›

№- Nazwa I* Numer części
005 REAR AXLE
Zastąpiono przez: A 617 350 20 00 		- A 385 350 05 01
005 REAR AXLE
WITH BRAKES,BRAKE DRUMS,HUBS,AND HAND BRAKE LINKAGE; RATIO: 47:9 		001 A 617 350 20 00
010 AXLE HOUSING
WITH REAR AXLE TUBES AND DIFFERENTIAL CASE BEARING CAPS 		001 A 617 350 46 20
BEARING BRACKET
(AXLE CASING),STEEL VERSION 		002 A 616 351 02 14
PLATE
(AXLE CASING),STEEL VERSION 		002 A 617 325 05 31
015 CYLINDRICAL PIN
BEARING COVER TO AXLE HOUSING 		004 N 000007 010203
020 SCREW
BEARING COVER TO AXLE HOUSING M 18X1,5X130 		004 A 005 990 21 04
025 PIN
AXLE TUBE TO AXLE HOUSING 		012 A 352 351 00 74
040 OIL COLLECTOR
REAR AXLE SHAFT 		002 A 385 357 01 82
045 THRUST RING
LEFT AND RIGHT 		002 A 385 356 00 15
050 SPACER WASHER
HUB TO REAR AXLE TUBE 		002 A 385 331 00 52
055 GROOVED NUT
HUB TO REAR AXLE TUBE 		004 A 617 356 00 26
060 LOCK PLATE
Zastąpiono przez: A 385 356 00 73 		- N 070952 085102
060 LOCK PLATE
HUB TO REAR AXLE TUBE 		002 A 385 356 00 73
065 FITTING
AXLE HOUSING BREATHING 		001 A 383 351 00 65
070 WHEEL HUB
CASTING 		002 A 385 356 13 01
075 WHEEL MOUNTING BOLT
Zastąpiono przez: A 000 401 40 71 		020 A 381 401 11 71
075 WHEEL MOUNTING BOLT 020 A 000 401 40 71
080 OIL COLLECTOR
WHEEL HUB 		002 A 385 356 02 82
085 BRAKE DRUM 002 A 385 423 03 01
095 TAPERED ROLLER BEARING
INSIDE 		002 A 001 980 66 02
095 TAPERED ROLLER BEARING
INSIDE 		002 A 005 981 84 05
095 TAPERED ROLLER BEARING
INSIDE 		002 A 005 981 85 05
095 TAPERED ROLLER BEARING
INSIDE 		002 A 006 981 01 05
100 TAPERED ROLLER BEARING
OUTSIDE 		002 A 001 980 67 02
100 TAPERED ROLLER BEARING
OUTSIDE 		002 A 005 981 83 05
100 TAPERED ROLLER BEARING
OUTSIDE 		002 A 005 981 86 05
100 TAPERED ROLLER BEARING
OUTSIDE 		002 A 005 981 99 05
105 REAR AXLE SHAFT
WITH INTERLOCK SERRATIONS 		002 A 385 357 55 01
110 GASKET
COVER TO WHEEL HUB 		002 A 317 356 00 80
113 REPAIR KIT
(PARTS KIT),REAR WHEEL HUB SEALING 		002 A 385 350 00 68
115 HUB CAP
WHEEL HUB 		002 A 615 356 00 20
120 LOCK WASHER
COVER TO WHEEL HUB 		016 N 912004 008102
125 SCREW
COVER TO WHEEL HUB 		016 N 000933 008145
130 SCREW PLUG
OIL DRAIN 		001 A 352 997 00 32
135 SCREW COLLAR 002 A 615 353 03 25
192 LOCK
SCREW COLLAR 		002 A 385 353 03 73
195 SCREW
LOCK TO COVER 		002 N 000933 008005
198 SET SCREW
RING GEAR CHECK 		001 A 385 353 03 76
201 SLIDE
RING GEAR CHECK 		001 A 385 353 01 49
204 NUT
SET SCREW 		001 N 000439 030202
207 SCREW
LOCK TO DIFFERENTIAL CASE BEARING COVER 		001 A 385 337 01 71
207 SCREW
LOCK TO DIFFERENTIAL CASE BEARING COVER 		001 A 385 351 00 71
213 NUT
Zastąpiono przez: N 304032 010003 		- N 000934 010014
213 NUT
LOCK TO DIFFERENTIAL CASE BEARING COVER 		001 N 304032 010003
216 GASKET
COVER TO REAR AXLE HOUSING 		001 A 651 351 00 80
219 COVER
REAR AXLE HOUSING 		001 A 617 351 02 08
222 SCREW
COVER TO REAR AXLE HOUSING 		016 N 914112 012018
225 SCREW PLUG
OIL FILLING 		001 A 352 997 00 32
228 DIFFERENTIAL GEAR
LESS RING GEAR AND PINION 		001 A 615 350 22 23
228 DIFFERENTIAL GEAR
LESS RING GEAR AND PINION 		001 A 615 350 26 23
231 SCREW
COVER TO STEEL DIFFERENTIAL CASE M 14X85 		012 A 005 990 51 04
231 SCREW
COVER TO CAST DIFFERENTIAL CASE M 14X100 		012 A 005 990 52 04
234 DIFFERENTIAL SPIDER 001 A 615 353 01 20
237 DIFFERENTIAL PINION

Zastąpiono przez: A 615 353 02 14 		- A 615 353 00 14
237 DIFFERENTIAL PINION
004 A 615 353 02 14
240 SPACER RING
DIFFERENTIAL PINION,BOTTOM 		004 A 615 353 00 51
240 SPACER RING
DIFFERENTIAL PINION,BOTTOM 		004 A 615 353 01 51
243 ROLLER
DIFFERENTIAL PINION 		160 A 615 981 01 86
246 SIDE GEAR

Zastąpiono przez: A 615 353 01 15 		- A 617 353 01 15
246 SIDE GEAR
002 A 615 353 01 15
249 THRUST WASHER
DIFFERENTIAL PINION,TOP 		004 A 615 353 01 62
252 SPACER RING
DIFFERENTIAL PINION,TOP 		004 A 615 353 02 51
255 REPAIR KIT
DIFFERENTIAL GEAR 		001 A 615 350 00 40
258 THRUST WASHER
AS REQUIRED 1.45 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 22 62
258 THRUST WASHER
AS REQUIRED 1.45 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 39 62
258 THRUST WASHER
AS REQUIRED 1.50 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 40 62
258 THRUST WASHER
AS REQUIRED 1.55 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 24 62
258 THRUST WASHER
AS REQUIRED 1.55 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 41 62
258 THRUST WASHER
AS REQUIRED 1.60 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 42 62
258 THRUST WASHER
AS REQUIRED 1.65 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 26 62
258 THRUST WASHER
AS REQUIRED 1.65 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 43 62
258 THRUST WASHER
AS REQUIRED 1.70 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 44 62
258 THRUST WASHER
AS REQUIRED 1.80 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 28 62
258 THRUST WASHER
AS REQUIRED 1.80 MM
ONLY INSTALL PARTS MADE OF THE SAME MATERIAL 		002 A 385 353 45 62
261 RING GEAR AND PINION
RATIO: 47:9 		001 A 385 350 41 39
264 SCREW
Zastąpiono przez: A 385 990 24 01 		- A 385 990 21 01
264 SCREW
RING GEAR TO DIFFERENTIAL CASE 		018 A 385 990 24 01
267 TAPERED ROLLER BEARING 002 A 004 981 17 05
267 TAPERED ROLLER BEARING 002 A 004 981 43 05
267 TAPERED ROLLER BEARING 002 A 005 981 56 05
267 TAPERED ROLLER BEARING 002 A 006 981 00 05
270 CYLINDR. ROLLER BEARING
Zastąpiono przez: A 007 981 79 01 		- A 004 981 67 01
270 CYLINDR. ROLLER BEARING
Zastąpiono przez: A 007 981 79 01 		- A 004 981 81 01
270 CYLINDR. ROLLER BEARING
Zastąpiono przez: A 007 981 79 01 		- A 004 981 86 01
270 CYLINDR. ROLLER BEARING
DRIVE PINION BEARING 		001 A 007 981 79 01
270 CYLINDR. ROLLER BEARING
DRIVE PINION BEARING 		001 A 007 981 78 01
273 LOCK RING
40X1.75 MM 		001 N 000471 040002
273 SNAP RING
40X1.50 MM 		001 N 912009 040100
276 SNAP RING 001 A 385 994 00 37
279 SPACER WASHER
AS REQUIRED 0.10 MM 		001 A 301 353 33 52
279 SPACER WASHER
AS REQUIRED 0.25 MM 		001 A 301 353 36 52
282 TAPERED ROLLER BEARING
ON PINION END 		001 A 006 981 34 05
282 TAPERED ROLLER BEARING
ON PINION END 		001 A 009 981 69 05
282 TAPERED ROLLER BEARING
ON PINION END 		001 A 006 981 35 05
285 TAPERED ROLLER BEARING
ON FLANGE END 		001 A 006 981 17 05
285 TAPERED ROLLER BEARING
ON FLANGE END 		001 A 006 981 19 05
288 SPACER RING
DRIVE PINION 		001 A 370 353 00 51
291 SPACER WASHER
AS REQUIRED 6.60 MM 		001 A 301 353 79 52
291 SPACER WASHER
AS REQUIRED 6.60 MM 		001 A 301 353 89 52
291 SPACER WASHER
AS REQUIRED 6.64 MM 		001 A 301 353 77 52
291 SPACER WASHER
AS REQUIRED 6.64 MM 		001 A 301 353 87 52
291 SPACER WASHER
AS REQUIRED 6.68 MM 		001 A 301 353 75 52
291 SPACER WASHER
AS REQUIRED 6.68 MM 		001 A 301 353 85 52
291 SPACER WASHER
AS REQUIRED 6.72 MM 		001 A 301 353 73 52
291 SPACER WASHER
AS REQUIRED 6.72 MM 		001 A 301 353 83 52
291 SPACER WASHER
AS REQUIRED 6.76 MM 		001 A 301 353 71 52
291 SPACER WASHER
AS REQUIRED 6.76 MM 		001 A 301 353 81 52
291 SPACER WASHER
AS REQUIRED 6.80 MM 		001 A 301 353 01 52
291 SPACER WASHER
AS REQUIRED 6.80 MM 		001 A 301 353 39 52
291 SPACER WASHER
AS REQUIRED 6.84 MM 		001 A 301 353 03 52
291 SPACER WASHER
AS REQUIRED 6.84 MM 		001 A 301 353 41 52
291 SPACER WASHER
AS REQUIRED 6.88 MM 		001 A 301 353 05 52
291 SPACER WASHER
AS REQUIRED 6.88 MM 		001 A 301 353 43 52
291 SPACER WASHER
AS REQUIRED 6.92 MM 		001 A 301 353 07 52
291 SPACER WASHER
AS REQUIRED 6.92 MM 		001 A 301 353 45 52
291 SPACER WASHER
AS REQUIRED 6.96 MM 		001 A 301 353 09 52
291 SPACER WASHER
AS REQUIRED 6.96 MM 		001 A 301 353 47 52
291 SPACER WASHER
AS REQUIRED 7.00 MM 		001 A 301 353 11 52
291 SPACER WASHER
AS REQUIRED 7.00 MM 		001 A 301 353 49 52
291 SPACER WASHER
AS REQUIRED 7.04 MM 		001 A 301 353 13 52
291 SPACER WASHER
AS REQUIRED 7.04 MM 		001 A 301 353 51 52
291 SPACER WASHER
AS REQUIRED 7.08 MM 		001 A 301 353 15 52
291 SPACER WASHER
AS REQUIRED 7.08 MM 		001 A 301 353 53 52
291 SPACER WASHER
AS REQUIRED 7.12 MM 		001 A 301 353 17 52
291 SPACER WASHER
AS REQUIRED 7.12 MM 		001 A 301 353 55 52
291 SPACER WASHER
AS REQUIRED 7.16 MM 		001 A 301 353 19 52
291 SPACER WASHER
AS REQUIRED 7.16 MM 		001 A 301 353 57 52
291 SPACER WASHER
AS REQUIRED 7.20 MM 		001 A 301 353 21 52
291 SPACER WASHER
AS REQUIRED 7.20 MM 		001 A 301 353 59 52
291 SPACER WASHER
AS REQUIRED 7.24 MM 		001 A 301 353 23 52
291 SPACER WASHER
AS REQUIRED 7.24 MM 		001 A 301 353 61 52
291 SPACER WASHER
AS REQUIRED 7.28 MM 		001 A 301 353 25 52
291 SPACER WASHER
AS REQUIRED 7.28 MM 		001 A 301 353 63 52
291 SPACER WASHER
AS REQUIRED 7.32 MM 		001 A 301 353 27 52
291 SPACER WASHER
AS REQUIRED 7.32 MM 		001 A 301 353 65 52
291 SPACER WASHER
AS REQUIRED 7.36 MM 		001 A 301 353 29 52
291 SPACER WASHER
AS REQUIRED 7.36 MM 		001 A 301 353 67 52
291 SPACER WASHER
AS REQUIRED 7.40 MM 		001 A 301 353 31 52
291 SPACER WASHER
AS REQUIRED 7.40 MM 		001 A 301 353 69 52
294 THRUST WASHER
DRIVE PINION 		001 A 385 353 38 62
297 SCREW COLLAR
DRIVE PINION 		001 A 615 353 01 25
300 SEAL RING
INSIDE 68X85X10 		001 A 016 997 66 47
302 SEAL RING
OUTSIDE 68X85X13 		001 A 016 997 67 47
305 LOCK
SCREW COLLAR 		001 A 327 353 03 73
308 LOCK
SCREW COLLAR 		001 A 385 353 05 73
315 SCREW
LOCK TO AXLE HOUSING 		001 N 000933 008005
320 FLANGE
150 MM 		001 A 385 353 10 45
330 NUT
FLANGE TO DRIVE PINION 		001 A 385 351 01 72
335 UNIT IDENTIFICATION PLATE
Zastąpiono przez: A 437 584 06 24 		001 A 385 584 70 24
335 UNIT IDENTIFICATION PLATE 001 A 437 584 06 24
340 RIVET
UNIT PLATE TO AXLE 		002 A 385 990 00 96
Aby dowiedzieć się, gdzie kupić przedmiot lub jego odpowiednika, kliknij na numerze katalogowym.

Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy
Region: EU | GB | USA