| №- | Nazwa | I* | Numer części |
|---|---|---|---|
| 010 | STEERING KNUCKLE LEFT |
001 | A 204 332 01 01 |
| 010 | STEERING KNUCKLE RIGHT |
001 | A 204 332 02 01 |
| 020 | CIRCUMFERENTIAL GASKET BETWEEN RPM SENSOR AND STEERING KNUCKLE |
002 | A 204 335 00 80 |
| 030 | FRONT WHEEL HUB LEFT |
001 | A 204 330 06 25 |
| 030 | FRONT WHEEL HUB RIGHT |
001 | A 204 330 06 25 |
| 040 | ELASTOMER-MOLDED SEAL WHEEL HUB, LEFT |
001 | A 204 330 00 60 |
| 040 | ELASTOMER-MOLDED SEAL WHEEL HUB, RIGHT |
001 | A 204 330 00 60 |
| 050 | NUT WHEEL HUB, LEFT |
001 | A 116 334 03 72 |
| 050 | NUT WHEEL HUB, RIGHT |
001 | A 116 334 03 72 |
| 060 | HEXALOBULAR BOLT WHEEL HUB, LEFT M6X25 |
001 | N 000000 003358 |
| 060 | HEXALOBULAR BOLT WHEEL HUB, RIGHT M6X25 |
001 | N 000000 003358 |
| 070 | PLUG WHEEL HUB, LEFT |
001 | A 168 357 00 89 |
| 070 | PLUG WHEEL HUB, RIGHT |
001 | A 168 357 00 89 |
| 080 | ANTI-FRICTION BEARING WHEEL HUB, LEFT |
001 | A 203 330 00 51 |
| 080 | ANTI-FRICTION BEARING WHEEL HUB, RIGHT |
001 | A 203 330 00 51 |
| 100 | STRUT LEFT WITHOUT BEARING Zastąpiono przez: A 204 330 87 11 |
001 | A 204 330 43 11 |
| 100 | STRUT ROD LEFT WITH BEARING |
001 | A 204 330 87 11 |
| 100 | STRUT RIGHT WITHOUT BEARING Zastąpiono przez: A 204 330 88 11 |
001 | A 204 330 44 11 |
| 100 | STRUT ROD RIGHT WITH BEARING |
001 | A 204 330 88 11 |
| 110 | HYDROMOUNT TENSION ROD LEFT THIS PART NUMBER CAN BE USED TO REQUEST A RETROFIT (SOFTWARE RETROFIT), ENABLE THEN TAKES PLACE VIA FDOK/VDOC, IMPLEMENTATION TAKES PLACE VIA THE SCN PROCESS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== |
001 | A 204 333 11 14 |
| 110 | HYDROMOUNT TENSION ROD RIGHT THIS PART NUMBER CAN BE USED TO REQUEST A RETROFIT (SOFTWARE RETROFIT), ENABLE THEN TAKES PLACE VIA FDOK/VDOC, IMPLEMENTATION TAKES PLACE VIA THE SCN PROCESS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== |
001 | A 204 333 11 14 |
| 120 | ELASTOMERIC CUP LEFT AND RIGHT AT STRUT ROD BEARING WHEN ORDERING, ENSURE FORM IS COMPLETED FULLY AND KEPT ON FILE."SPARE-KEY/LOCKING LUG PART ORDERS". IN THE EVENT OF CRIMINAL INVESTIGATION DOCUMENTARY EVIDENCE MUST BE FURNISHED AT ANY GIVEN TIME. |
004 | A 211 333 06 97 |
| 130 | HEXAGON HEAD BOLT TORQUE STRUT TO INTEGRAL CARRIER, LEFT M14X1.5X120 |
001 | N 910105 014022 |
| 130 | HEXAGON HEAD BOLT TORQUE STRUT TO INTEGRAL CARRIER, RIGHT M14X1.5X120 |
001 | N 910105 014022 |
| 130 | ADJUSTMENT SCREW LEFT, FOR ADJUSTING ONLY |
001 | A 212 333 00 71 |
| 130 | ADJUSTMENT SCREW RIGHT, FOR ADJUSTING ONLY |
001 | A 212 333 00 71 |
| 140 | SPACER DISK TORQUE STRUT TO INTEGRAL CARRIER, LEFT |
002 | A 220 333 00 76 |
| 140 | SPACER DISK TORQUE STRUT TO INTEGRAL CARRIER, RIGHT |
002 | A 220 333 00 76 |
| 140 | HEXAGON NUT CROSS STRUT TO INTEGRAL CARRIER M14X1.5 |
001 | N 000000 008261 |
| 140 | NUT W FLANGE, BINDING FOR ADJUSTING WORK ONLY M14X1.5 |
001 | A 002 990 51 54 |
| 150 | HEXAGON NUT TORQUE STRUT TO FRAME-TYPE INT. SUPP. M14X1.5 |
002 | N 000000 008261 |
| 150 | NUT W FLANGE, BINDING FOR ADJUSTING WORK ONLY M14X1.5 |
002 | A 002 990 51 54 |
| 200 | CROSS STRUT LEFT |
001 | A 204 330 67 11 |
| 200 | CROSS STRUT RIGHT |
001 | A 204 330 68 11 |
| 220 | HEXAGON HEAD BOLT CROSS STRUT TO LEFT INTEGRAL CARRIER M14X1.5X120 |
001 | N 910105 014022 |
| 220 | HEXAGON HEAD BOLT CROSS STRUT TO RIGHT INTEGRAL CARRIER M14X1.5X120 |
001 | N 910105 014022 |
| 220 | ADJUSTMENT SCREW LEFT, FOR ADJUSTING ONLY |
001 | A 212 333 00 71 |
| 220 | ADJUSTMENT SCREW RIGHT, FOR ADJUSTING ONLY |
001 | A 212 333 00 71 |
| 230 | SPACER DISK CROSS STRUT TO LEFT INTEGRAL CARRIER |
002 | A 220 333 00 76 |
| 230 | SPACER DISK CROSS STRUT TO RIGHT INTEGRAL CARRIER |
002 | A 220 333 00 76 |
| 230 | RS SPACER RING LEFT, FOR ADJUSTING ONLY |
002 | A 221 333 01 77 |
| 230 | RS SPACER RING RIGHT, FOR ADJUSTING ONLY |
002 | A 221 333 01 77 |
| 240 | HEXAGON NUT CROSS STRUT TO INTEGRAL CARRIER M14X1.5 |
001 | N 000000 008261 |
| 240 | NUT W FLANGE, BINDING FOR ADJUSTING WORK ONLY M14X1.5 |
001 | A 002 990 51 54 |
| 250 | HEXAGON NUT CROSS STRUT TO STEERING KNUCKLE, LEFT M14X1,5 IMPORTANT: WHEN ORDERING, CITE ADDITIONAL KEY ES-2: 0041. |
001 | A 005 990 48 50 |
| 250 | HEXAGON NUT CROSS STRUT TO STEERING KNUCKLE, RIGHT M14X1,5 IMPORTANT: WHEN ORDERING, CITE ADDITIONAL KEY ES-2: 0041. |
001 | A 005 990 48 50 |
| 270 | HEXAGON NUT STRUT TO STEERING KNUCKLE M14X1,5 IMPORTANT: WHEN ORDERING, CITE ADDITIONAL KEY ES-2: 0041. |
002 | A 005 990 48 50 |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy