EXHAUST SYSTEM USED ON SIX-CYLINDER GASOLINE VEHICLES
| №- | Nazwa | I* | Numer części |
|---|---|---|---|
| 010 | EXHAUST GAS LINE LEFT PART IS ONLY OR ALSO SUPPLIED AS RECONDITIONED PART |
001 | A 172 490 21 19 |
| 010 | EXHAUST GAS LINE LEFT PART IS ONLY OR ALSO SUPPLIED AS RECONDITIONED PART |
001 | A 172 490 19 19 |
| 020 | EXHAUST GAS LINE RIGHT PART IS ONLY OR ALSO SUPPLIED AS RECONDITIONED PART |
001 | A 172 490 20 19 |
| 020 | EXHAUST LINE RIGHT PART IS ONLY OR ALSO SUPPLIED AS RECONDITIONED PART |
001 | A 172 490 17 19 |
| 030 | BOLT AND WASHER ASSY. FRONT EXHAUST PIPE TO EXHAUST MANIFOLD M8 X 55 |
004 | A 170 990 00 10 |
| 040 | VIBRATION ABSORBER FRONT LEFT |
001 | A 172 491 04 47 |
| 045 | BOLT MOUNTING VIBRATION ABSORBER 8X70 |
001 | A 001 990 48 00 |
| 050 | SCREENING PLATE VIBRATION ABSORBER |
001 | A 164 491 00 30 |
| 060 | BRACKET EXHAUST PIPE FRONT LEFT TO EXHAUST PIPE FRONT RIGHT |
001 | A 171 492 11 41 |
| 065 | NUT EXHAUST PIPE FRONT LEFT TO EXHAUST PIPE FRONT RIGHT M8 |
002 | A 129 990 04 58 |
| 070 | NOX SENSOR FRONT L=615MM WHEN ORDERING SPECIFY ES1 = 12 OUT DATA FROM VEHICLE. Zastąpiono przez: A 000 905 70 00 |
002 | A 000 905 30 00 |
| 070 | NOX SENSOR FRONT L=615MM THIS PART NUMBER CAN BE USED TO REQUEST A RETROFIT (SOFTWARE RETROFIT), ENABLE THEN TAKES PLACE VIA FDOK/VDOC, IMPLEMENTATION TAKES PLACE VIA THE SCN PROCESS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== WHEN ORDERING SPECIFY ES1 = 12 OUT DATA FROM VEHICLE. Zastąpiono przez: A 000 905 35 03 |
002 | A 000 905 70 00 |
| 070 | NOX SENSOR FRONT L=615MM THIS PART NUMBER CAN BE USED TO REQUEST A RETROFIT (SOFTWARE RETROFIT), ENABLE THEN TAKES PLACE VIA FDOK/VDOC, IMPLEMENTATION TAKES PLACE VIA THE SCN PROCESS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== WITH DAS4, MAKE SURE TO PERFORM THE FOLLOWING COMMAND WITH XENTRY DIAGNOSTICS PRIOR TO ORDERING: "REGISTER VEHICLE FOR ORDERIN G A PROGRAMMED KEY" Zastąpiono przez: A 000 905 62 04 |
002 | A 000 905 35 03 |
| 070 | NOX SENSOR FRONT |
002 | A 000 905 62 04 |
| 080 | TEMPERATURE SENSOR UPSTREAM CATALYTIC CONVERTER FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. Zastąpiono przez: A 000 905 78 01 |
002 | A 007 153 78 28 |
| 080 | TEMPERATURE SENSOR UPSTREAM CATALYTIC CONVERTER FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. |
002 | A 000 905 78 01 |
| 080 | TEMPERATURE SENSOR UPSTREAM CATALYTIC CONVERTER NOTE WORK INSTRUCTIONS IN WIS WIS-NET#AR77.35-P-1100V# ROM THE NEW REAR SEALING RAIL, IN WHICH CASE THIS IS ALSO TO BE EXCHANGED |
002 | A 000 905 21 05 |
| 090 | NUT SENSOR CABLE TO FRAME M6 |
004 | N 000000 003477 |
| 100 | OXYGEN SENSOR LEFT CONTROL PROBE IN FRONT OF CATALYST |
001 | A 003 542 69 18 |
| 100 | LAMBDA PROBE RIGHT CONTROL PROBE IN FRONT OF CATALYST |
001 | A 008 542 85 18 |
| 100 | LAMBDA PROBE LEFT CONTROL PROBE IN FRONT OF CATALYST |
001 | A 009 542 55 18 |
| 100 | LAMBDA PROBE LEFT DIAGNOSTIC SENSOR IN CATALYTIC CONVERTER |
001 | A 006 542 20 18 |
| 100 | LAMBDA PROBE LEFT CONTROL PROBE IN FRONT OF CATALYST |
001 | A 009 542 61 18 |
| 100 | LAMBDA PROBE LEFT DIAGNOSTIC SENSOR IN CATALYTIC CONVERTER |
001 | A 006 542 22 18 |
| 100 | LAMBDA PROBE RIGHT DIAGNOSTIC SENSOR IN CATALYTIC CONVERTER |
001 | A 006 542 20 18 |
| 100 | OXYGEN SENSOR RIGHT CONTROL PROBE IN FRONT OF CATALYST |
001 | A 003 542 69 18 |
| 100 | LAMBDA PROBE RIGHT CONTROL PROBE IN FRONT OF CATALYST |
001 | A 009 542 55 18 |
| 100 | LAMBDA PROBE | 001 | A 008 542 69 18 |
| 100 | LAMBDA PROBE RIGHT CONTROL PROBE IN FRONT OF CATALYST |
001 | A 009 542 61 18 |
| 110 | CABLE HOLDER O2 SENSOR MOUNT |
001 | A 220 546 18 43 |
| 115 | CLIP FASTENING, NOX SENSOR LINE TO SHIELD 18.0X18.5 MM |
006 | A 000 546 20 75 |
| 120 | BRACKET LINE TO BRACKET 18 X 24 MM |
001 | A 000 541 01 40 |
| 120 | BRACKET 18 X 24 MM |
001 | A 000 541 01 40 |
| 130 | BRACKET OXYGEN SENSOR |
001 | A 204 546 33 43 |
| 135 | HEXALOBULAR BOLT BRACKET AT FRONT FLOOR M6X12 |
001 | N 910143 006000 |
| 140 | BRACKET OXYGEN SENSOR TO CRANKCASE, LEFT REAR |
001 | A 172 546 13 43 |
| 145 | HEXALOBULAR BOLT BRACKET TO CRANKCASE M6X12 |
001 | N 910143 006000 |
| 150 | CLAMP SENSOR LINE FASTENING |
002 | N 000000 000319 |
| 155 | NUT SENSOR LINE FASTENING |
002 | A 000 990 36 62 |
| 160 | BRACKET SENSOR LINE AT RIGHT TRANSMISSION BELL HOUSING WHEN ORDERING SPECIFY ES1 = 12 |
001 | A 276 150 34 73 |
| 160 | BRACKET SENSOR LINE AT RIGHT TRANSMISSION BELL HOUSING ====================================================================================I I WORKSHOP KEY ORDER FBS3 I I ============================================I=============================I=========I I I I USE I I ES2 I I I I ============================================I=============================I=========I I I I BLOCK KEY TRACK I USING WORKSHOP KEY I NO.0100 I I I I RELEASE KEY TRACK I USING WORKSHOP KEY I NO.0101 I I I I PERSONALIZE REPLACEMENT EZS BE SURE TO I I I I I I SPECIFY THE FIRST 16 DIGITS OF THE SERIAL I I I I I I NUMBER FROM NEW EZS I USING WORKSHOP KEY I NO.0102 I I I I ACTIVATE REPLACEMENT EIS I USING WORKSHOP KEY I NO.0103 I I I I REMOVE REPLACEMENT ELV TRANSP. PROTECTION I USING WORKSHOP KEY I NO.0104 I I I I PERSONALIZE REPLACEMENT ELV I USING WORKSHOP KEY I NO.0105 I I I I ACTIVATE REPLACEMENT ELV I USING WORKSHOP KEY I NO.0106 I I I I EIS DISGNOSIS I USING WORKSHOP KEY I NO.0107 I I I I ELV ELEC. STG. COLUMN ADJUSTMENT DIAGNOSIS I USING WORKSHOP CODE I NO.0108 I I I I KEY TRACK CONDITION IN VEHICLE I I I I DISPLAY I USING WORKSHOP KEY I NO.0109 I I LAST KEY USED I USING WORKSHOP KEY I NO.0110 I I KEY UTILIZATION VERIFICATION. I BY MEANS OF WORKSHOP KEY... I NO.0111 I I I I ====================================================================================I |
001 | A 276 150 48 73 |
| 160 | BRACKET SENSOR LINE AT LEFT TRANSMISSION BELLH OUSING |
001 | A 276 150 35 73 |
| 165 | SPRING CLAMP FOR SENSOR CONNECTOR 28X24 MM |
002 | A 000 991 01 70 |
| 165 | SPRING CLAMP FOR 4-PIN SENSOR |
002 | A 000 991 43 70 |
| 170 | HEXALOBULAR BOLT FASTENING BRACKET LEFT M8X20 |
002 | N 000000 000276 |
| 170 | HEXALOBULAR BOLT FASTENING BRACKET RIGHT M8X20 |
002 | N 000000 000276 |
| 180 | BRACKET SENSOR LINE AT LEFT TRANSMISSION BELLH OUSING |
001 | A 278 150 14 73 |
| 180 | BRACKET SENSOR LINE AT LEFT TRANSMISSION BELLH OUSING IN VEHICLES UP TO IDENT NO: F002349 THE REAR SEALING RAIL A1726700138 / A1726700238 IN LUSTER INSTALLED EX WORKS MAY DIFFER FR OM THE NEW FRONT SEALING RAIL, IN WHICH CASE THIS IS ALSO TO BE EXCHANGED |
001 | A 278 150 19 73 |
| 180 | BRACKET SENSOR LINE AT RIGHT TRANSMISSION BELL HOUSING |
001 | A 278 150 15 73 |
| 185 | HEXALOBULAR BOLT RIGHT BRACKET M6X15 |
001 | N 000000 001114 |
| 190 | SEAL RING FRONT EXHAUST PIPE TO REAR EXH. PIPE (FIXED) |
001 | A 204 492 00 81 |
| 200 | CLAMP CENTRAL REAR EXHAUST PIPE TO REAR EXHAUST PIPE 60 MM |
002 | A 000 490 13 41 |
| 210 | CENTER MUFFLER CENTRAL |
001 | A 172 491 16 01 |
| 215 | PROTECTIVE COVER TO CENTER MUFFLER |
001 | A 172 491 00 30 |
| 220 | BRACKET CENTRAL MUFFLER,LEFT |
001 | A 171 492 08 41 |
| 220 | BRACKET CENTRAL MUFFLER,RIGHT |
001 | A 171 492 04 41 |
| 230 | SUSPENSION RING CENTRAL MUFFLER,LEFT |
001 | A 203 492 01 44 |
| 230 | SUSPENSION RING CENTRAL MUFFLER,RIGHT |
001 | A 203 492 01 44 |
| 235 | HEXAGON HEAD BOLT LEFT BRACKET TO BODY M8X16 |
001 | N 910105 008008 |
| 235 | HEXAGON HEAD BOLT BRACKET RIGHT TO BODY M8X16 |
001 | N 910105 008008 |
| 240 | PIPE CLAMP F EXHAUST SYS. EXHAUST PIPE TO REAR EXHAUST PIPE Ø 48 MM |
002 | A 172 995 00 02 |
| 250 | VIBRATION ABSORBER TO MUFFLER |
001 | A 172 491 04 47 |
| 255 | BOLT VIBRATION DAMPER TO EXHAUST PIPE 8X70 |
001 | A 001 990 48 00 |
| 260 | SCREENING PLATE VIBRATION ABSORBER |
001 | A 164 491 00 30 |
| 270 | REAR MUFFLER REAR LEFT |
001 | A 172 491 17 01 |
| 280 | TAIL PIPE COVER REAR LEFT EXHAUST PIPE |
001 | A 171 490 11 27 |
| 280 | PANEL REAR LEFT EXHAUST PIPE |
001 | A 171 490 05 27 |
| 290 | BRACKET REAR MUFFLER LEFT |
002 | A 171 492 08 41 |
| 295 | HEXAGON HEAD BOLT LEFT AND RIGHT REAR MUFFLER BRACKETS TO BODY M8X16 |
002 | N 910105 008008 |
| 300 | SUSPENSION RING REAR MUFFLER LEFT |
002 | A 203 492 01 44 |
| 310 | REAR MUFFLER REAR RIGHT |
001 | A 172 491 20 01 |
| 310 | REAR MUFFLER REAR RIGHT |
001 | A 172 491 24 01 |
| 320 | TAIL PIPE COVER REAR RIGHT EXHAUST PIPE |
001 | A 171 490 12 27 |
| 320 | PANEL REAR RIGHT EXHAUST PIPE |
001 | A 171 490 06 27 |
| 330 | BRACKET REAR MUFFLER RIGHT |
002 | A 171 492 06 41 |
| 340 | SUSPENSION RING REAR MUFFLER RIGHT |
002 | A 203 492 01 44 |
| 505 | HEXALOBULAR BOLT BRACKET MOUNTING M6X16 |
003 | N 910143 006001 |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy