| №- | Name | A* | Part number |
|---|---|---|---|
| 010 | ANTINOISE CAPSULE FRONT TO BE ADAPTED DURING ASSEMBLY FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. SEE WIS FOR REPAIR INSTRUCTIONS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== |
001 | A 204 520 07 23 |
| 010 | COVER F ENGINE COMP. BM FRONT |
001 | A 204 524 23 30 |
| 020 | BRACKET LEFT |
001 | A 204 524 13 40 |
| 030 | BRACKET RIGHT |
001 | A 204 524 14 40 |
| 040 | HEXALOBULAR BOLT BRACKET LEFT AND RIGHT AT FLEXIBLE CROSSMEMBER M6X20 |
004 | N 910143 006002 |
| 060 | ENCAPSULATION CENTRAL TO BE ADAPTED DURING ASSEMBLY FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. SEE WIS FOR REPAIR INSTRUCTIONS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== Replaced by: A 204 520 26 23 |
001 | A 204 520 08 23 |
| 060 | ENCAPSULATION CENTRAL TO BE ADAPTED DURING ASSEMBLY FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. SEE WIS FOR REPAIR INSTRUCTIONS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== Replaced by: A 204 520 28 23 |
001 | A 204 520 26 23 |
| 060 | ENCAPSULATION CENTRAL TO BE ADAPTED DURING ASSEMBLY FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. SEE WIS FOR REPAIR INSTRUCTIONS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== |
001 | A 204 520 28 23 |
| 060 | PROTECTIVE PLATE CENTRAL |
001 | A 204 524 01 01 |
| 100 | PANELING REAR Replaced by: A 204 524 27 30 |
001 | A 204 524 04 30 |
| 100 | COVER F ENGINE COMP. BM REAR Replaced by: A 204 524 29 30 |
001 | A 204 524 27 30 |
| 100 | COVER F ENGINE COMP. BM REAR Replaced by: A 204 524 36 30 |
001 | A 204 524 29 30 |
| 100 | COVER F ENGINE COMP. BM REAR |
001 | A 204 524 36 30 |
| 100 | COVER F ENGINE COMP. BM REAR Replaced by: A 204 524 36 30 |
001 | A 204 524 29 30 |
| 100 | COVER F ENGINE COMP. BM REAR |
001 | A 204 524 36 30 |
| 110 | BRACKET LEFT FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. |
001 | A 204 524 03 40 |
| 110 | BRACKET LEFT ATTENTION: ORDER WASHER AS WELL MUST BE PAINTED BEFORE INSTALL. IN 7167 (DEEP DARK GRAY) OBSERVE WIS |
001 | A 204 524 25 40 |
| 110 | BRACKET RIGHT OBSERVE WIS NOTE SERVICE INFORMATION IN WIS WIS-NET#SI72.00-P-0008A# IMPORTANT: PART ONLY VALID W/ CODE 808/809/800/801 THIS PART NUMBER CAN BE USED TO REQUEST A RETROFIT (SOFTWARE RETROFIT), ENABLE THEN TAKES PLACE VIA FDOK/VDOC, IMPLEMENTATION TAKES PLACE VIA THE SCN PROCESS. ALSO REPLACE RESERVOIR |
001 | A 204 524 15 40 |
| 110 | BRACKET RIGHT ATTENTION: ORDER WASHER AS WELL MUST BE PAINTED BEFORE INSTALL. IN 7167 (DEEP DARK GRAY) OBSERVE WIS |
001 | A 204 524 24 40 |
| 110 | BRACKET RIGHT |
001 | A 204 524 28 40 |
| 130 | HEXAGON NUT W COLLAR BRACKET TO MAIN FLOOR 5 MM |
004 | A 210 990 01 50 |
| 150 | SHEET METAL SCREW FRONT TRIM TO BRACKET 4.8X19 |
002 | A 001 990 60 36 |
| 150 | SHEET METAL SCREW FRONT TRIM TO FRAME-TYPE INTEGRALSUPPORT 4.8X19 |
002 | A 001 990 60 36 |
| 150 | SHEET METAL SCREW PANELING FRONT TO WHEELHOUSE PANEL 4.8X19 |
002 | A 001 990 60 36 |
| 150 | SHEET METAL SCREW CENTRAL COVERING TO FRAME-TYPE INTEGRAL SUPPORT 4.8X19 |
006 | A 001 990 60 36 |
| 150 | SHEET METAL SCREW REAR PANEL TO WHEELHOUSE LINER 4.8X19 |
002 | A 001 990 60 36 |
| 150 | SHEET METAL SCREW REAR PANEL TO LONGITUDINAL MEMBER 4.8X19 |
004 | A 001 990 60 36 |
| 150 | SHEET METAL SCREW REAR PANEL TO BRACKET 4.8X19 |
002 | A 001 990 60 36 |
| 160 | CLIP-TYPE NUT FRONT TRIM TO BRACKET 4,8 |
002 | A 004 994 31 45 |
| 160 | CLIP-TYPE NUT FRONT TRIM TO FRAME-TYPE INTEGRALSUPPORT 4,8 |
002 | A 004 994 31 45 |
| 160 | CLIP-TYPE NUT CENTRAL COVERING TO FRAME-TYPE INTEGRAL SUPPORT 4,8 |
006 | A 004 994 31 45 |
| 160 | CLIP-TYPE NUT REAR PANEL TO LONGITUDINAL MEMBER |
004 | A 001 994 98 45 |
| 160 | CLIP-TYPE NUT REAR PANEL TO BRACKET 4,8 |
002 | A 004 994 31 45 |
| 170 | HEXAGON HEAD BOLT PROTECTIVE SHIELD TO FRAME-TYPE INTEGRAL SUPPORT, FRONT M8X25 ATTENTION: ORDER WASHER AS WELL |
004 | N 304017 008034 |
| 170 | HEXAGON HEAD BOLT PROTECTIVE SHIELD TO FRAME-TYPE INTEGRAL SUPPORT, REAR M8X25 ATTENTION: ORDER WASHER AS WELL |
002 | N 304017 008034 |
| 175 | WASHER PROTECTIVE SHIELD TO FRAME-TYPE INTEGRAL SUPPORT, FRONT |
004 | N 000000 003250 |
| 175 | WASHER PROTECTIVE SHIELD TO FRAME-TYPE INTEGRAL SUPPORT, REAR |
002 | N 000000 003250 |
| 180 | SPRING NUT PROTECTIVE SHIELD TO FRAME-TYPE INTEGRAL SUPPORT, FRONT M8 |
004 | A 004 994 18 45 |
| 180 | SPRING NUT PROTECTIVE SHIELD TO FRAME-TYPE INTEGRAL SUPPORT, REAR M8 |
002 | A 004 994 18 45 |
| 200 | STRUT BETWEEN LONGITUDINAL MEMBER ANDFRAME-TYPE INTEGRAL SUPPORT |
002 | A 204 524 11 47 |
| 210 | HEXAGON HEAD BOLT STRUT TO SIDE MEMBER M10X20 IMPORTANT: WITH 2-WHEEL DRIVEN VEHICLES, THE WASHER MUST ALSO BE ORDERED |
002 | N 000000 005053 |
| 212 | WASHER STRUT TO SIDE MEMBER |
002 | N 001440 012005 |
| 220 | HEXAGON HEAD BOLT STRUT TO FRAME-TYPE INTEGRAL SUPPORT M10X20 |
002 | N 000000 005053 |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy