WHEELHOUSE,FRONT SUBFRAME

EPC / Mercedes / Car / FG / FG 207.459 / 62 / 030
‹ ›

№- Name A* Part number
010 LONGITUDINAL MEMBER
LEFT

THIS PART NUMBER CAN BE USED TO REQUEST A RETROFIT (SOFTWARE RETROFIT), ENABLE THEN TAKES PLACE VIA FDOK/VDOC, IMPLEMENTATION
TAKES PLACE VIA THE SCN PROCESS.
=================================================================================================
SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION:
A 001 546 99 41 GREEN 0.7 - 2.4 MM2
A 002 546 00 41 RED 2.0 - 4.0 MM2
A 002 546 01 41 BLUE 3.5 - 8.0 MM2
A 002 546 11 41 YELLOW 7.5 - 12.0 MM2
BUTT JOINT:
A 002 546 13 41 0.5 MM2
A 002 546 14 41 0.8 MM2
A 002 546 15 41 1.3 MM2
A 002 546 16 41 2.0 MM2
===================================================================================================
Replaced by: A 204 620 01 50 		001 A 204 620 61 34
010 WHEEL HOUSE
LEFT

THIS PART NUMBER CAN BE USED TO REQUEST A RETROFIT (SOFTWARE RETROFIT), ENABLE THEN TAKES PLACE VIA FDOK/VDOC, IMPLEMENTATION
TAKES PLACE VIA THE SCN PROCESS.
=================================================================================================
SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION:
A 001 546 99 41 GREEN 0.7 - 2.4 MM2
A 002 546 00 41 RED 2.0 - 4.0 MM2
A 002 546 01 41 BLUE 3.5 - 8.0 MM2
A 002 546 11 41 YELLOW 7.5 - 12.0 MM2
BUTT JOINT:
A 002 546 13 41 0.5 MM2
A 002 546 14 41 0.8 MM2
A 002 546 15 41 1.3 MM2
A 002 546 16 41 2.0 MM2
=================================================================================================== 		001 A 204 620 01 50
020 COVER LONGITUDINAL MEMBER
LEFT

THIS PART NUMBER CAN BE USED TO REQUEST A RETROFIT (SOFTWARE RETROFIT), ENABLE THEN TAKES PLACE VIA FDOK/VDOC, IMPLEMENTATION
TAKES PLACE VIA THE SCN PROCESS.
=================================================================================================
SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION:
A 001 546 99 41 GREEN 0.7 - 2.4 MM2
A 002 546 00 41 RED 2.0 - 4.0 MM2
A 002 546 01 41 BLUE 3.5 - 8.0 MM2
A 002 546 11 41 YELLOW 7.5 - 12.0 MM2
BUTT JOINT:
A 002 546 13 41 0.5 MM2
A 002 546 14 41 0.8 MM2
A 002 546 15 41 1.3 MM2
A 002 546 16 41 2.0 MM2
=================================================================================================== 		001 A 204 620 15 67
030 SIDE MEMBER
LEFT 		001 A 204 620 45 34
040 ANGLE
LEFT SIDE MEMBER 		001 A 204 626 13 12
050 BRACKET
LEFT

IMPORTANT! FOR CONVERSION TO 18 INCH WHEELS, THE TIRE ROD RETROFIT KIT MUST ALSO BE ORDERED! 		001 A 207 620 11 14
060 STRIKING PLATE
LEFT
Replaced by: A 204 620 05 87 		001 A 204 626 07 52
060 LONGITUDINAL MEMBER
LEFT 		001 A 204 620 05 87
070 BRACKET
LEFT REAR FENDER 		001 A 204 889 01 14
080 LONGITUDINAL MEMBER
TOP LEFT 		001 A 204 630 59 40
090 PLATE
ON UPPER CARRIER 		003 A 202 626 07 11
110 CROSS MEMBER
LEFT, PEDAL FLOOR PANEL 		001 A 204 626 05 55
120 STRUT
LEFT 		001 A 204 630 63 40
150 SIDE MEMBER
RIGHT
Replaced by: A 204 620 02 50 		001 A 204 620 42 34
150 WHEEL HOUSE
RIGHT 		001 A 204 620 02 50
160 COVER
RIGHT 		001 A 204 620 12 67
170 SIDE MEMBER
RIGHT 		001 A 204 620 44 34
180 ANGLE
RIGHT SIDE MEMBER 		001 A 204 626 13 12
190 BRACKET
RIGHT

IMPORTANT! FOR CONVERSION TO 18 INCH WHEELS, THE TIRE ROD RETROFIT KIT MUST ALSO BE ORDERED! 		001 A 207 620 12 14
200 STRIKING PLATE
RIGHT
Replaced by: A 204 620 06 87 		001 A 204 626 08 52
200 LONGITUDINAL MEMBER
RIGHT 		001 A 204 620 06 87
210 BRACKET
RIGHT REAR FENDER 		001 A 204 889 02 14
220 LONGITUDINAL MEMBER
TOP RIGHT 		001 A 204 630 60 40
230 PLATE
ON UPPER CARRIER 		003 A 202 626 07 11
250 CROSS MEMBER
RIGHT, PEDAL FLOOR PANEL 		001 A 204 626 06 55
260 STRUT
RIGHT 		001 A 204 630 64 40
300 INTEGRAL CARRIER 001 A 204 628 10 57
300 INTEGRAL CARRIER 001 A 204 628 06 57
310 BLIND CLINCH NUT
IN FRAME-TYPE INTEGRAL SUPPORT M10 		001 A 000 990 49 59
320 BOLT
FRONT FRAME-TYPE INTEGRAL SUPPORT M14X1,5-SGX50 		002 A 000 990 14 11
330 BOLT
REAR FRAME-TYPE INTEGRAL SUPPORT M14X1,5-SGX100 		002 A 000 990 15 11
340 EXPANSION PLUG
INTEGRAL SUPPORT 15.5 MM
FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO.
002 A 110 987 10 44
340 EXPANSION PLUG
INTEGRAL SUPPORT 20.5 MM

FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. 		002 A 113 987 00 44
350 FASTENING PLATE
STEERING TO FRAME-TYPE INTEGRAL SUPPORT 		001 A 207 626 01 11
350 FASTENING PLATE
STEERING TO FRAME-TYPE INTEGRAL SUPPORT 		001 A 207 628 00 11
360 HEXAGON HEAD BOLT
PLATE AT FRONT FRAME-TYPE INTEGRAL SUPPORT M12X1.5X20 		002 N 910105 012003
360 HEXAGON HEAD BOLT
PLATE AT FRONT FRAME-TYPE INTEGRAL SUPPORT M10X25 		002 N 910105 010009
360 HEXAGON HEAD BOLT
MOUNTING PLATE TO FRONT END M12X1.5X20 		002 N 910105 012003
360 HEXAGON HEAD BOLT
PLATE AT FRONT FRAME-TYPE INTEGRAL SUPPORT M12X1.5X20 		002 N 910105 012003
370 NUT
PLATE AT FRONT FRAME-TYPE INTEGRAL SUPPORT M12X1.5 		002 N 913023 012002
370 NUT
PLATE AT FRONT FRAME-TYPE INTEGRAL SUPPORT M12X1.5 		002 N 913023 012002
370 NUT
MOUNTING PLATE TO FRONT END M12X1.5 		002 N 913023 012002
400 SUPPORT
INTEGRAL SUPPORT 		002 A 204 628 01 26
410 HEXALOBULAR BOLT
SUPPORT AT BODY M12X1,5X30

NOT SUITABLE FOR VEHICLES WITH XENON HEADLAMPS 		002 N 910143 012008
420 DEFLECTOR RAMP
LEFT 		001 A 204 628 01 08
420 DEFLECTOR RAMP
LEFT 		001 A 204 628 01 08
420 DEFLECTOR RAMP
RIGHT 		001 A 204 628 00 08
420 DEFLECTOR RAMP
RIGHT 		001 A 204 628 00 08
500 STRUT
LEFT

IMPORTANT! FOR CONVERSION TO 18 INCH WHEELS, THE TIRE ROD RETROFIT KIT MUST ALSO BE ORDERED! 		001 A 207 628 11 24
500 STRUT
RIGHT 		001 A 207 628 12 24
510 BOLT
FASTENING STRUT 		001 A 001 990 40 03
520 NUT
STRUT HOLDER LEFT AND RIGHT M8 		002 N 000000 003175
800 BOLT
REPAIR SOLUTION FOR RUPTURED WELDED PINS 		NB A 000 990 12 10
810 BLIND RIVET
REPAIR SOLUTION 6,4 X 12MM / 1-3,5MM
NO LONGER AVAILABLE

RIVET IS ONLY VALID FOR MODEL SERIES 222. FOR REPAIR INFORMATION SEE WIS. ADDITIONAL INFORMATION VIA TECHNICAL MARKET SUPPORT. 		NB A 000 991 76 32
To find out where to buy the item or equivalent, click on the part number.

Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy
Region: EU | GB | USA