| №- | Name | A* | Part number |
|---|---|---|---|
| 010 | STEERING KNUCKLE LEFT |
001 | A 204 332 01 01 |
| 010 | STEERING KNUCKLE RIGHT |
001 | A 204 332 02 01 |
| 030 | FRONT WHEEL HUB LEFT AND RIGHT |
002 | A 204 330 06 25 |
| 040 | ELASTOMER-MOLDED SEAL WHEEL HUB, LEFT |
001 | A 204 330 00 60 |
| 040 | ELASTOMER-MOLDED SEAL WHEEL HUB, RIGHT |
001 | A 204 330 00 60 |
| 050 | NUT WHEEL HUB, LEFT |
001 | A 116 334 03 72 |
| 050 | NUT WHEEL HUB, RIGHT |
001 | A 116 334 03 72 |
| 060 | HEXALOBULAR BOLT WHEEL HUB, LEFT M6X25 |
001 | N 000000 003358 |
| 060 | HEXALOBULAR BOLT WHEEL HUB, RIGHT M6X25 |
001 | N 000000 003358 |
| 070 | PLUG WHEEL HUB, LEFT |
001 | A 168 357 00 89 |
| 070 | PLUG WHEEL HUB, RIGHT |
001 | A 168 357 00 89 |
| 080 | ANTI-FRICTION BEARING WHEEL HUB, LEFT |
001 | A 203 330 00 51 |
| 080 | ANTI-FRICTION BEARING WHEEL HUB, RIGHT |
001 | A 203 330 00 51 |
| 200 | STRUT LEFT WITHOUT BEARING Replaced by: A 204 330 87 11 |
001 | A 204 330 43 11 |
| 200 | STRUT ROD LEFT WITH BEARING THIS PART NUMBER CAN BE USED TO REQUEST A RETROFIT (SOFTWARE RETROFIT), ENABLE THEN TAKES PLACE VIA FDOK/VDOC, IMPLEMENTATION TAKES PLACE VIA THE SCN PROCESS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== |
001 | A 204 330 87 11 |
| 200 | STRUT RIGHT WITHOUT BEARING Replaced by: A 204 330 88 11 |
001 | A 204 330 44 11 |
| 200 | STRUT ROD RIGHT WITH BEARING THIS PART NUMBER CAN BE USED TO REQUEST A RETROFIT (SOFTWARE RETROFIT), ENABLE THEN TAKES PLACE VIA FDOK/VDOC, IMPLEMENTATION TAKES PLACE VIA THE SCN PROCESS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== |
001 | A 204 330 88 11 |
| 210 | RUBBER BUSHING TENSION ROD LEFT IMPORTANT! FOR CONVERSION TO 18 INCH WHEELS, THE TIRE ROD RETROFIT KIT MUST ALSO BE ORDERED! Replaced by: A 204 333 11 14 |
001 | A 203 333 10 14 |
| 210 | HYDROMOUNT TENSION ROD LEFT IMPORTANT! FOR CONVERSION TO 18 INCH WHEELS, THE TIRE ROD RETROFIT KIT MUST ALSO BE ORDERED! |
001 | A 204 333 11 14 |
| 210 | RUBBER BUSHING TENSION ROD RIGHT IMPORTANT! FOR CONVERSION TO 18 INCH WHEELS, THE TIRE ROD RETROFIT KIT MUST ALSO BE ORDERED! Replaced by: A 204 333 11 14 |
001 | A 203 333 10 14 |
| 210 | HYDROMOUNT TENSION ROD RIGHT IMPORTANT! FOR CONVERSION TO 18 INCH WHEELS, THE TIRE ROD RETROFIT KIT MUST ALSO BE ORDERED! |
001 | A 204 333 11 14 |
| 220 | ELASTOMERIC CUP LEFT AND RIGHT AT STRUT ROD BEARING FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. |
002 | A 211 333 06 97 |
| 220 | ELASTOMERIC CUP LEFT AND RIGHT AT STRUT ROD BEARING |
002 | A 211 333 06 97 |
| 230 | HEXAGON HEAD BOLT TORQUE STRUT TO INTEGRAL CARRIER, LEFT M14X1.5X120 |
001 | N 910105 014022 |
| 230 | HEXAGON HEAD BOLT TORQUE STRUT TO INTEGRAL CARRIER, RIGHT M14X1.5X120 |
001 | N 910105 014022 |
| 230 | ADJUSTMENT SCREW FOR ADJUSTING WORK ONLY |
002 | A 212 333 00 71 |
| 240 | SPACER DISK TORQUE STRUT TO INTEGRAL CARRIER, LEFT |
002 | A 220 333 00 76 |
| 240 | SPACER DISK TORQUE STRUT TO INTEGRAL CARRIER, RIGHT |
002 | A 220 333 00 76 |
| 240 | RS SPACER RING FOR ADJUSTING WORK ONLY |
004 | A 221 333 01 77 |
| 250 | HEXAGON NUT TORQUE STRUT TO FRAME-TYPE INT. SUPP. M14X1,5 THE OLD PART MUST NO LONGER BE INSTALLED Replaced by: N 000000 008261 |
001 | N 000000 003281 |
| 250 | HEXAGON NUT TORQUE STRUT TO FRAME-TYPE INT. SUPP. M14X1.5 |
002 | N 000000 008261 |
| 250 | HEXAGON NUT TORQUE STRUT TO FRAME-TYPE INT. SUPP. M14X1,5 Replaced by: N 000000 008261 |
001 | N 000000 003281 |
| 250 | NUT W FLANGE, BINDING FOR ADJUSTING WORK ONLY M14X1.5 |
002 | A 002 990 51 54 |
| 260 | TS BOLT FOR ADJUSTING WORK ONLY |
002 | A 000 333 09 71 |
| 280 | HEXAGON NUT TORQUE STRUT AT STEERING KNUCKLE, LEFT M14X1,5 FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. |
001 | N 000000 003281 |
| 280 | HEXAGON NUT TORQUE STRUT AT STEERING KNUCKLE, LEFT M14X1,5 NOT SUITABLE FOR VEHICLES WITH XENON HEADLAMPS |
001 | A 005 990 48 50 |
| 280 | HEXAGON NUT TORQUE STRUT AT STEERING KNUCKLE, RIGHT M14X1,5 FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. |
001 | N 000000 003281 |
| 280 | HEXAGON NUT TORQUE STRUT AT STEERING KNUCKLE, RIGHT M14X1,5 NOT SUITABLE FOR VEHICLES WITH XENON HEADLAMPS |
001 | A 005 990 48 50 |
| 300 | CROSS STRUT LEFT |
001 | A 204 330 67 11 |
| 300 | CROSS STRUT RIGHT |
001 | A 204 330 68 11 |
| 320 | HEXAGON HEAD BOLT CROSS STRUT TO LEFT INTEGRAL CARRIER M14X1.5X120 |
001 | N 910105 014022 |
| 320 | HEXAGON HEAD BOLT CROSS STRUT TO RIGHT INTEGRAL CARRIER M14X1.5X120 |
001 | N 910105 014022 |
| 320 | ADJUSTMENT SCREW FOR ADJUSTING WORK ONLY |
002 | A 212 333 00 71 |
| 330 | SPACER DISK CROSS STRUT TO LEFT INTEGRAL CARRIER |
002 | A 220 333 00 76 |
| 330 | SPACER DISK CROSS STRUT TO RIGHT INTEGRAL CARRIER |
002 | A 220 333 00 76 |
| 330 | RS SPACER RING FOR ADJUSTING WORK ONLY |
004 | A 221 333 01 77 |
| 340 | HEXAGON NUT CROSS STRUT TO LEFT INTEGRAL CARRIER M14X1,5 THE OLD PART MUST NO LONGER BE INSTALLED Replaced by: N 000000 008261 |
001 | N 000000 003281 |
| 340 | HEXAGON NUT CROSS STRUT TO LEFT INTEGRAL CARRIER M14X1.5 |
001 | N 000000 008261 |
| 340 | HEXAGON NUT CROSS STRUT TO RIGHT INTEGRAL CARRIER M14X1,5 THE OLD PART MUST NO LONGER BE INSTALLED Replaced by: N 000000 008261 |
001 | N 000000 003281 |
| 340 | HEXAGON NUT CROSS STRUT TO RIGHT INTEGRAL CARRIER M14X1.5 |
001 | N 000000 008261 |
| 340 | NUT W FLANGE, BINDING FOR ADJUSTING WORK ONLY M14X1.5 |
002 | A 002 990 51 54 |
| 350 | TS BOLT FOR ADJUSTING WORK ONLY |
002 | A 000 333 09 71 |
| 370 | HEXAGON NUT CROSS STRUT TO STEERING KNUCKLE, LEFT M14X1,5 FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. |
001 | N 000000 003281 |
| 370 | HEXAGON NUT CROSS STRUT TO STEERING KNUCKLE, LEFT M14X1,5 NOT SUITABLE FOR VEHICLES WITH XENON HEADLAMPS |
001 | A 005 990 48 50 |
| 370 | HEXAGON NUT CROSS STRUT TO STEERING KNUCKLE, RIGHT M14X1,5 FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. |
001 | N 000000 003281 |
| 370 | HEXAGON NUT CROSS STRUT TO STEERING KNUCKLE, RIGHT M14X1,5 NOT SUITABLE FOR VEHICLES WITH XENON HEADLAMPS |
001 | A 005 990 48 50 |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy