ELECTRICAL EQUIPMENT AT ENGINE

EPC / Mercedes / Car / FG / FG 121.002 / 15 / 008
‹ ›

№- Name A* Part number
001 STARTER MOTOR
WITH PUSH BUTTON OPERATION 		001 A 000 151 77 01
002 ROLLER FREEWHEEL 001 A 000 151 20 13
003 SOLENOID SWITCH STARTER 001 A 000 152 10 11
004 SET OF CARBON BRUSHES
4 PIECES 		001 A 000 151 14 14
005 PRESSURE SPRING
FOR CARBON BRUSH 		004 A 000 151 05 93
006 BEARING BUSHING
IN DRIVE BEARING 		001 A 000 151 07 50
007 BEARING BUSHING
IN COMMUTATOR BEARING 		001 A 000 151 08 50
008 INTERMEDIATE FLANGE
FOR STARTER MOTOR AT CLUTCH HOUSING 		001 A 120 151 00 12
009 HEX. -HD. SCREW
M 12X80 DIN 931-8 G FOR STARTER MOTOR AT CLUTCH HOUSING 		002
010 WASHER
13 DIN 433 FOR STARTER MOTOR AT CLUTCH HOUSING 		002
011 LOCK WASHER
B 12 DIN 127 FOR STARTER MOTOR AT CLUTCH HOUSING 		002
012 HEX. NUT
M 12 DIN 934-5 S FOR STARTER MOTOR AT CLUTCH HOUSING 		002
GENERATOR
MARK: RED POINT UP TO ENGINE 6500103 		001 A 000 154 25 02
013 GENERATOR
MARK: YELLOW POINT FROM ENGINE 6500104 		001 A 000 154 48 02
014 SET OF CARBON BRUSHES
2 PIECES 		001 A 000 154 27 14
015 PRESSURE SPRING
FOR CARBON BRUSH 		002 A 000 154 06 93
016 THREE -
ELEMENT VOLTAGE REGULATOR SEE ALSO GROUP 54 		001 A 000 154 55 06
017 PULLEY
OPTIONAL FOR GENERATOR 		001 A 180 155 07 15
PULLEY
OPTIONAL FOR GENERATOR 		001 A 180 155 08 15
018 WOODRUFF KEY
3X5 DIN 6888 FOR PULLEY AT GENERATOR HAS TO BE DELIVERED WITH GENERATOR 		001
019 LOCK WASHER
B 12 DIN 127 FOR PULLEY AT GENERATOR HAS TO BE DELIVERED WITH GENERATOR 		001
020 HEX. NUT
M 12X1,5 DIN 936-5 S FOR PULLEY AT GENERATOR HAS TO BE DELIVERED WITH GENERATOR 		001
021 SUPPORT
FOR GENERATOR 		001 A 121 155 08 35
LOCK WASHER
B 8 DIN 127 FOR SUPPORT AT CYLINDER CRANKCASE UP TO ENGINE 6500522 		002
HEX. NUT
M 8 DIN 934-5 S FOR SUPPORT AT CYLINDER CRANKCASE UP TO ENGINE 6500522 		002
022 LOCK WASHER
B 10 DIN 127 FOR SUPPORT AT CYLINDER CRANKCASE FROM ENGINE 6500523 		002
023 HEX. NUT
M 10 DIN 934-5 S FOR SUPPORT AT CYLINDER CRANKCASE FROM ENGINE 6500523 		002
024 GROUND CABLE
FOR SUPPORT AT GENERATOR 		001 A 121 150 03 32
025 HEX. -HD. SCREW
M 8X35 DIN 931-8 G FOR GENERATOR AT SUPPORT 		001
SLEEVE
FOR GENERATOR AT SUPPORT UP TO ENGINE 6500264 		001 A 180 991 06 40
RUBBER WASHER
FOR GENERATOR AT SUPPORT UP TO ENGINE 6500264 		002 A 121 155 00 81
WASHER
FOR GENERATOR AT SUPPORT UP TO ENGINE 6500264 		002 A 120 155 00 82
026 INTERMEDIATE WASHER
FOR GENERATOR AT SUPPORT FROM ENGINE 6500265 		002 A 121 155 00 76
029 LOCK WASHER
B 8 DIN 127 FOR GENERATOR AT SUPPORT 		001
030 HEX. NUT
M 8 DIN 934-5 S FOR GENERATOR AT SUPPORT 		001
031 HEX. -HD. SCREW
M 8X60 DIN 931-8 G FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001
032 SLEEVE
FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001 A 180 991 06 40
033 RUBBER WASHER
FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		002 A 120 155 00 81
034 WASHER
FOR GENERATOR SUSPENSION, RUBBER MOUNTED FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		002 A 120 155 00 82
035 WASHER
FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001 A 121 990 01 40
036 SPACER SLEEVE,
25.5-MM LONG FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001 A 121 155 00 53
037 LOCK WASHER
B 8 DIN 127 FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001
038 HEX. NUT
M 8 DIN 934-5 S FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001
039 TIGHTENING SCREW
FOR GENERATOR ADJUSTMENT 		001 A 121 155 01 23
040 TIGHTENING NUT
FOR GENERATOR ADJUSTMENT 		001 A 121 155 00 72
041 CLAMPING PIECE
FOR GENERATOR ADJUSTMENT FROM ENGINE 7505525 		001 A 121 155 01 28
042 HEX. NUT
M 8 DIN 934-5 S FOR GENERATOR ADJUSTMENT 		001
SLEEVE
FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE UP TO ENGINE 6500264 		001 A 120 991 03 40
RUBBER WASHER
FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE UP TO ENGINE 6500264 		002 A 120 155 00 81
WASHER
FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE UP TO ENGINE 6500264 		002 A 120 155 00 82
043 INTERMEDIATE WASHER
FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE FROM ENGINE 6500265 		002 A 121 155 00 76
046 LOCK WASHER
B 8 DIN 127 FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE 		001
047 HEX. NUT
M 8 DIN 934-5 S FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE 		001
HEX. -HD. SCREW
M 8X40 DIN 931-8 G FOR CLAMPING PIECE AT GENERATOR UP TO ENGINE 7505524 		001
048 HEX. -HD. SCREW
M 8X30 DIN 931-8 G FOR CLAMPING PIECE AT GENERATOR FROM ENGINE 7505525 		001
049 LOCK WASHER
B 8 DIN 127 FOR CLAMPING PIECE AT GENERATOR 		001
HEX. NUT
M 8 DIN 934-5 S FOR CLAMPING PIECE AT GENERATOR UP TO ENGINE 7505524 		001
055 IGNITION DISTRIBUTOR
WITH COUPLING AND VACUUM ADJUSTING DEVICE INTERFERENCE-FREE FROM ENGINE 9501269 		001 A 000 158 73 01
IGNITION DISTRIBUTOR
WITH COUPLING AND VACUUM ADJUSTING DEVICE INTERFERENCE - FREE EXPORT - SPECIAL REQUEST (DUST - PROOF DESIGN) FROM ENGINE 		001 A 000 158 74 01
056 DISTRIBUTOR PLATE
WITH CARBON BRUSH 		001 A 000 158 06 02
057 CARBON BRUSH WITH SPRING 001 A 000 158 00 34
058 OILER IN HOUSING 001 A 000 158 04 89
059 CONTACT SET 001 A 000 158 07 90
061 DISTRIBUTOR ROTOR
WITH COUNTER WEIGHT DUST-PROOF AND INTERFERENCE-FREE 		001 A 000 158 15 31
DUST PROTECTIVE COVER
EXPORT - SPECIAL REQUEST 		001 A 000 158 00 11
062 LEAF SPRING
FOR DISTRIBUTOR PLATE 		002 A 000 158 03 33
063 FIXING SHACKLE
WITHOUT NOSE 		001 A 000 158 03 40
064 FIXING SHACKLE WITH NOSE 001 A 000 158 04 40
065 CYLINDRICAL SCREW
AM 4X8 DIN 84-4 S FOR FIXING SHACKLE WITH LEAF SPRING AT IGNITION DISTRIBUTOR 		002
066 LOCK WASHER
B 4 DIN 127 FOR FIXING SHACKLE WITH LEAF SPRING AT IGNITION DISTRIBUTOR 		002
CONDENSER AT HOUSING
UP TO ENGINE 9501268 		001 A 000 156 11 01
067 CONDENSER AT HOUSING
FROM ENGINE 9501269 		001 A 000 156 49 01
068 FIXING CLAMP
FOR CONDENSER AT IGNITION DISTRIBUTOR FROM ENGINE 9501269 		001 A 000 158 06 40
CYLINDRICAL SCREW
AM 4X5 DIN 84-5 S FOR CONDENSER AT IGNITION DISTRIBUTOR 		002
LOCK WASHER
B 4 DIN 127 FOR CONDENSER AT IGNITION DISTRIBUTOR 		002
VACUUM ADJUSTING DEVICE
UP TO ENGINE 9501268 		001 A 000 158 04 18
070 VACUUM ADJUSTING DEVICE
FROM ENGINE 9501269 		001 A 000 158 05 18
071 CYLINDRICAL SCREW
AM 4X5 DIN 84-5 S FOR VACUUM ADJUSTING DEVICE AT IGNITION DISTRIBUTOR 		002
072 LOCK WASHER
B 4 DIN 127 FOR VACUUM ADJUSTING DEVICE AT IGNITION DISTRIBUTOR 		002
COUPLING
ON SHAFT UP TO ENGINE 9501268 		001 A 000 158 03 09
073 COUPLING
ON SHAFT FROM ENGINE 9501269 		001 A 000 158 05 09
074 FIBER WASHER
FOR COUPLING AT IGNITION DISTRIBUTOR 		002 A 000 158 01 76
075 SHIM 0.1 MM THICK
FOR COUPLING AT IGNITION DISTRIBUTOR OPTIONAL 		NB A 000 158 00 52
SHIM 0.2 MM THICK
FOR COUPLING AT IGNITION DISTRIBUTOR OPTIONAL 		NB A 000 158 04 52
PIN
FOR COUPLING AT IGNITION DISTRIBUTOR UP TO ENGINE 9501268 		001 A 000 158 04 74
076 PIN
FOR COUPLING AT IGNITION DISTRIBUTOR FROM ENGINE 9501269 		001 A 000 158 07 74
76a SNAP RING
FOR COUPLING AT IGNITION DISTRIBUTOR FROM ENGINE 9501269 		001 A 000 158 02 77
077 THREADED BUSHING 001 A 000 158 00 59
078 SEALING RING 001 A 000 158 02 60
080 BEARING, IGNITION
DISTRIBUTOR FROM ENGINE 6500026 		001 A 121 150 02 07
081 ADJUSTING LEVER
WITH ANGLE UP TO ENGINE 8511499 		001 A 180 150 01 24
81a ADJUSTING LEVER
FROM ENGINE 8511500 		001 A 180 150 03 24
082 HEX. -HD. SOCKET SCREW
M 6X25 DIN 912-8 G 		001
82a ADJUSTING ECCENTRIC
FROM ENGINE 8511500 		001 A 180 150 02 24
SPRING WASHER
B 6 DIN 137 FOR ADJUSTER LEVER AT ADJUSTING EXCENTRIC FROM ENGINE 8511500 		001
HEX. -HD. SCREW
M 6X8 DIN 933-8 G FOR ADJUSTER LEVER AT ADJUSTING EXCENTRIC FROM ENGINE 8511500 		001
083 HEX. -HD. SCREW
M 5X30 S DIN 931-8G FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8511499 		001
084 WASHER
5,3 DIN 125 FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8511499 		001
085 HELICAL SPRING
FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8511499 		001 A 136 933 08 01
086 HEX. NUT
M 5 DIN 934-5 S FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8511499 		001
087 COTTER PIN
1 X 12 DIN 94 FOR ADJUSTING LEVER AT BEARING 		001
088 HEX. -HD. SCREW WITH PIN
AM 6X12 DIN 561-5 S FOR FIXING OF IGNITION DISTRIBUTOR UP TO ENGINE 8511499 		001
089 PRESSURE SPRING
FOR IGNITION TIMING UP TO ENGINE 8511499 		001 A 186 993 24 01
ADJUSTING SCREW
FOR IGNITION TIMING UP TO ENGINE 7506870 		001 A 186 158 00 70
HEX. NUT
M 10X1 DIN 936-5 S FOR IGNITION TIMING UP TO ENGINE 7506870 		001
RUBBER SLEEVE
FOR IGNITION TIMING UP TO ENGINE 7506870 		001 A 186 158 00 83
DAMPING RUBBER
FOR IGNITION TIMING UP TO ENGINE 7506870 		001 A 186 158 01 83
SLEEVE
FOR IGNITION TIMING UP TO ENGINE 7506870 		001 A 186 158 00 51
CLAMPING CHUCK
FOR WIRE CABLE, IGNITION TIMING UP TO ENGINE 7506870 		001 A 198 150 00 29
090 ADJUSTING SCREW
FOR ADJUSTING LEVER AT BEARING FROM ENGINE 7506871 UP TO 8511499 		001 A 121 150 00 84
091 KNURLED NUT
FOR ADJUSTING SCREW FROM ENGINE 7506871 UP TO 8511499 		001 A 121 990 00 57
094 WASHER
FOR ADJUSTING SCREW FROM ENGINE 7506871 UP TO 8511499 		001 A 121 158 00 76
097 BEARING WITH BUSHING
FOR IGNITION DISTRIBUTOR AND OIL PUMP HOUSING 		001 A 180 150 01 07
098 HELICAL GEAR
FOR IGNITION DISTRIBUTOR DRIVE 		001 A 180 158 04 12
100 INTERMEDIATE RING
FOR BEARING, IGNITION DISTRIBUTOR, AT CYLINDER CRANKCASE FROM ENGINE 6500026 		001 A 121 158 00 51
101 HEX. -HD. SOCKET SCREW
M 8X45 DIN 912-8 G FOR BEARING, IGNITION DISTRIBUTOR, AT CYLINDER CRANKCASE FROM ENGINE 6500026 		001
102 WASHER
8,4 DIN 125 FOR BEARING, IGNITION DISTRIBUTOR, AT CYLINDER CRANKCASE FROM ENGINE 6500026 		001
HEX. -HD. SCREW
M 8X10 DIN 933-8 G FOR LOCKING OF THREADED BORE AT CYLINDER CRANKCASE UP TO ENGINE 6514359 		001
VACUUM PIPE
UP TO ENGINE 9501268 		001 A 121 150 00 35
104 VACUUM PIPE
FROM ENGINE 9501269 		001 A 121 150 03 35
105 SCREW
4 DIN 3871 		001
106 DOUBLE CONE RING
4 DIN 3862 		001
107 RUBBER HOSE 001 A 181 997 03 82
108 HOSE STRAP 002 A 181 997 00 90
109 SPRING CLAMP
FOR FUEL PIPE AND VACUUM PIPE 		002 A 180 993 05 25
HEX. -HD. SCREW
M 5X10 DIN 933-8 G FOR FUEL PIPE AND VACUUM PIPE UP TO ENGINE 7522096 		001
LOCK WASHER
B 5 DIN 127 FOR FUEL PIPE AND VACUUM PIPE UP TO ENGINE 7522096 		001
HEX. NUT
M 5 DIN 934-5 S FOR FUEL PIPE AND VACUUM PIPE UP TO ENGINE 7522096 		001
113 SEALING RING
A 6X12 DIN 7603 A1 FOR VACUUM CONNECTION AT CARBURETOR 		001
114 CONNECTION FITTING
FOR VACUUM CONNECTION AT CARBURETOR 		001 A 181 158 01 37
114a GROUND CABLE
FROM IGNITION DISTRIBUTOR TO CYLINDER HEAD FROM ENGINE 6511911 		001 A 121 150 02 32
115 IGNITION CABLE
HARNESS WITH PROTECTIVE TUBE 		001 A 121 150 03 19
116 IGNITION CABLE PLUG
MAKE BOSCH OPTIONAL 		004 A 000 156 15 10
IGNITION CABLE PLUG
MAKE BERU OPTIONAL 		004 A 000 156 20 10
117 CABLE SLEEVE 004 A 000 159 00 38
118 RAIN PROTECTIVE CAP
FOR IGNITION CABLE 		004 A 000 159 00 85
119 GROMMET
FOR PROTECTIVE TUBE 		004 A 000 997 22 81
120 IGNITION CABLE
FOR IGNITION COIL, DISTRIBUTOR 		001 A 180 150 06 18
CABLE SLEEVE 002 A 000 159 00 38
RAIN PROTECTIVE CAP
FOR IGNITION CABLE 		002 A 000 159 00 85
PLUG FOR
INTERFERENCE SUPPRESSION MAKE BOSCH OPTIONAL SPECIAL REQUEST - FOR RADIO INSTALLATION 		005 A 000 156 17 10
PLUG FOR
INTERFERENCE SUPPRESSION MAKE BERU OPTIONAL SPECIAL REQUEST - FOR RADIO INSTALLATION 		005 A 000 156 21 10
RUBBER CAP
SPECIAL REQUEST - FOR RADIO INSTALLATION 		005 A 000 159 07 85
121 GROMMET 002 A 159 546 00 37
122 CABLE TERMINAL
4X0,8 N 261 		001
123 CABLE TERMINAL
5X0,8 N 261 		001
124 LOCK WASHER
B 6 DIN 127 FOR PROTECTIVE TUBE AT CYLINDER HEAD 		002
125 HEX. -HD. SCREW
M 6X10 DIN 933-8 G FOR PROTECTIVE TUBE AT CYLINDER HEAD 		002
126 SPARK PLUG
MAKE BOSCH OPTIONAL 		004 A 000 159 59 03
SPARK PLUG
MAKE BERU OPTIONAL 		004 A 000 159 75 03
SPARK PLUG,
INTERFERENCE-FREE MAKE BOSCH OPTIONAL SPECIAL REQUEST FOR INSTALLATION OF RADIO AND 300 WATT GENERATOR 		004 A 000 159 55 03
SPARK PLUG,
INTERFERENCE-FREE MAKE BERU OPTIONAL SPECIAL REQUEST FOR INSTALLATION OF RADIO AND 300 WATT GENERATOR 		004 A 000 159 78 03
127 SEALING RING
C 14X20 DIN 7603 ST. ASB. FOR SPARK PLUG AT CYLINDER HEAD HAS TO BE DELIVERED WITH SPARK PLUG 		004
128 IGNITION COIL
AT FRONT WALL SEE GROUP 54 		001 A 000 158 00 03
To find out where to buy the item or equivalent, click on the part number.

Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy
Region: EU | GB | USA