| №- | Наименование | К* | Номер детали | A |
|---|---|---|---|---|
CRANKSHAFT |
- | XXX XXX XXX XXXX | - | |
| CRANKSHAFT WITH COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS MAKE GLYCO OPTIONAL |
001 | A 62 103 019 01 | - | |
| CRANKSHAFT WITH COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS MAKE LAUCHERTHAL OPTIONAL |
001 | A 62 103 020 01 | - | |
| 001 | CRANKSHAFT WITH COUNTERWEIGHT AND FLYWHEEL |
001 | A 62 103 011 01 | - |
| 002 | SHIM, 5.45 MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 | A 18 003 100 52 | - |
| SHIM, 5.60 MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 | A 18 003 101 52 | - | |
| SHIM, 5.75 MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 | A 18 003 102 52 | - | |
| SHIM, 5.90 MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 | A 18 003 103 52 | - | |
| SHIM, 6.05 MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 | A 18 003 104 52 | - | |
| 003 | WOODRUFF KEY ON CRANKSHAFT, FRONT 5 X 7,5 DIN 6888 |
001 | - | |
| 004 | CRANKSHAFT GEAR ON CRANKSHAFT, FRONT |
001 | A 18 005 202 03 | - |
| 005 | OIL SLINGER RING ON CRANKSHAFT, FRONT |
001 | A 18 003 104 25 | - |
| 05a | COUNTERWEIGHT | 001 | A 12 103 103 07 | - |
| 05b | SPACER RING FOR CRANKSHAFT, OIL SLINGER RING |
001 | A 12 103 100 51 | - |
| 006 | CYLINDRICAL PIN 8 H8 X 8 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT |
001 | - | |
| 007 | CYLINDRICAL PIN 8 H8 X 16 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT |
001 | - | |
| 008 | FLYWHEEL WITH | 001 | A 62 103 003 05 | - |
| 009 | STARTER RING | 001 | A 62 103 201 05 | - |
| 010 | NECKED-DOWN BOLT FOR FLYWHEEL AT CRANKSHAFT |
006 | A 12 103 106 71 | - |
| 011 | CYLINDRICAL PIN 10 H8 X 18 DIN 7 FOR FLYWHEEL AT CRANKSHAFT |
001 | - | |
| 013 | COLLAR SCREW | 001 | A 18 603 102 71 | - |
| 014 | SEALING RING AT CRANKSHAFT, FRONT |
001 | A 12 003 101 81 | - |
| 14a | ADJUSTING NEEDLE FOR TOP DEAD CENTER ADJUSTMENT |
001 | A 12 103 200 15 | - |
| PIN AT CYLINDER CRANKCASE | 001 | A 62 103 200 74 | - | |
| 015 | PULLEY DIA. 122 MM UP TO ENGINE |
001 | A 12 120 001 05 | - |
| PULLEY DIA. 135 MM FROM ENGINE |
001 | A 62 120 001 05 | - | |
| 016 | ANNULAR GROOVED BEARING 6202 DIN 625 FOR DRIVE SHAFT AT CRANKSHAFT |
001 | - | |
| 017 | LOCKING RING FOR DRIVE SHAFT AT CRANKSHAFT |
001 | A 18 603 100 33 | - |
| 018 | FABRIC SEALING RING 75 X 87 X 6 GL N 255 A FOR CRANKSHAFT SEALING IN CYLINDER CRANKCASE, REAR |
001 | - | |
CRANKSHAFT BEARING |
- | XXX XXX XXX XXXX | - | |
| 020 | SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 70-MM = STANDARD (MAKE GLYCO) OPTIONAL READY FOR INSTALLATION |
001 | A 12 103 005 97 | - |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 70-MM = STANDARD (MAKE LAUCHERTHAL) OPTIONAL READY FOR INSTALLATION |
001 | A 62 103 000 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 70-MM = STANDARD (MAKE VANDERVELL) OPTIONAL READY FOR INSTALLATION |
001 | A 12 103 010 97 | - | |
| 021 | CRANKSHAFT BEARING SHELL MAKE GLYCO WITH GROOVE;USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BE |
004 | A 12 103 314 01 | - |
| CRANKSHAFT BEARING SHELL MAKE LAUCHERTHAL WITH GROOVE;USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN |
004 | A 62 103 300 01 | - | |
| CRANKSHAFT BEARING SHELL MAKE VANDERVELL WITH GROOVE;USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENT |
004 | A 12 103 319 01 | - | |
| 022 | CRANKSHAFT BEARING SHELL MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 12 103 314 02 | - |
| CRANKSHAFT BEARING SHELL MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 62 103 300 02 | - | |
| CRANKSHAFT BEARING SHELL MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 12 103 319 02 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.75-MM = REPAIR SIZEI MAKE GLYCO OPTIONAL READY FOR INSTALLATION |
001 | A 12 103 006 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.75-MM = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION |
001 | A 62 103 001 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.75-MM = REPAIR SIZE I MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION |
001 | A 12 103 011 97 | - | |
| CRANKSHAFT BEARING SHELL, MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CENTER B |
004 | A 12 103 315 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CE |
004 | A 62 103 301 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CEN |
004 | A 12 103 320 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 12 103 315 02 | - | |
| CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 62 103 301 02 | - | |
| CRANKSHAFT BEARING SHELL, MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 12 103 320 02 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MM=REPAIR SIZE II MAKE GLYCO OPTIONAL READY FOR INSTALLATION |
001 | A 12 103 007 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MM=REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION |
001 | A 62 103 002 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MM=REPAIR SIZE II MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION |
001 | A 12 103 012 97 | - | |
| CRANKSHAFT BEARING SHELL, MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B |
004 | A 12 103 316 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE |
004 | A 62 103 302 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN |
004 | A 12 103 321 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 12 103 316 02 | - | |
| CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 62 103 302 02 | - | |
| CRANKSHAFT BEARING SHELL, MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 12 103 321 02 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.25-MM = REPAIR SIZE III MAKE GLYCO READY FOR INSTALLATION |
001 | A 12 103 008 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.25-MM=REPAIR SIZE III MAKE LAUCHERTHAL READY FOR INSTALLATION |
001 | A 62 103 003 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.25-MM=REPAIR SIZE III MAKE VANDERVELL READY FOR INSTALLATION |
001 | A 12 103 013 97 | - | |
| CRANKSHAFT BEARING SHELL, MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CENTER B |
004 | A 12 103 317 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CE |
004 | A 62 103 303 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CEN |
004 | A 12 103 322 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 12 103 317 02 | - | |
| CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 62 103 303 02 | - | |
| CRANKSHAFT BEARING SHELL, MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 12 103 322 02 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.00-MM = REPAIR SIZE IV, MAKE GLYCO OPTIONAL READY FOR INSTALLATION |
001 | A 12 103 009 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.00-MM = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION |
001 | A 62 103 004 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.00-MM = REPAIR SIZE IV MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION |
001 | A 12 103 014 97 | - | |
| CRANKSHAFT BEARING SHELL, MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B |
004 | A 12 103 318 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE |
004 | A 62 103 304 01 | - | |
| CRANKSHAFT BEARING SHELL MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN |
004 | A 12 103 323 01 | - | |
| CRANKSHAFT BEARING SHELL, MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 12 103 318 02 | - | |
| CRANKSHAFT BEARING SHELL, MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 62 103 304 02 | - | |
| CRANKSHAFT BEARING SHELL MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL |
002 | A 12 103 323 02 | - | |
CONNECTING ROD |
- | XXX XXX XXX XXXX | - | |
| 025 | CONNECTING ROD | 004 | A 62 103 005 20 | - |
| 026 | CONNECTING ROD BUSHING | 004 | A 62 103 800 50 | - |
| 027 | CONNECTING SCREW | 008 | A 12 103 803 71 | - |
| 028 | NUT | 008 | A 18 203 800 72 | - |
| CONNECTING ROD BUSHING, EXTERIOR DIA. 29.5-MM REPAIR DESIGN |
004 | A 62 103 801 50 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE GLYCO OPTIONAL Заменено на: A 121 038 28 10 |
- | A 12 103 828 11 | - | |
| 029 | CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE GLYCO OPTIONAL |
008 | A 12 103 828 10 | - |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE LAUCHERTHAL OPTIONAL Заменено на: A 121 038 07 10 |
- | A 12 103 807 11 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE LAUCHERTHAL OPTIONAL |
008 | A 12 103 807 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE VANDERVELL OPTIONAL |
008 | A 12 103 833 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE GLYCO OPTIONAL Заменено на: A 121 038 29 10 |
- | A 12 103 829 11 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE GLYCO OPTIONAL |
008 | A 12 103 829 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL Заменено на: A 121 038 08 10 |
- | A 12 103 808 11 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL |
008 | A 12 103 808 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE VANDERVELL OPTIONAL |
008 | A 12 103 834 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE GLYCO OPTIONAL Заменено на: A 121 038 30 10 |
- | A 12 103 830 11 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE GLYCO OPTIONAL |
008 | A 12 103 830 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL Заменено на: A 121 038 09 10 |
- | A 12 103 809 11 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL |
008 | A 12 103 809 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II, MAKE VANDERVELL OPTIONAL |
008 | A 12 103 835 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III OPTIONAL Заменено на: A 121 038 31 10 |
- | A 12 103 831 11 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III OPTIONAL |
008 | A 12 103 831 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III MAKE LAUCHERTHAL OPTIONAL Заменено на: A 121 038 10 10 |
- | A 12 103 810 11 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III MAKE LAUCHERTHAL OPTIONAL |
008 | A 12 103 810 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III MAKE VANDERVELL OPTIONAL |
008 | A 12 103 836 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE GLYCO OPTIONAL Заменено на: A 121 038 32 10 |
- | A 12 103 832 11 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE GLYCO OPTIONAL |
008 | A 12 103 832 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL Заменено на: A 121 038 11 10 |
- | A 12 103 811 11 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL |
008 | A 12 103 811 10 | - | |
| CONNECTING ROD BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV, MAKE VANDERVELL OPTIONAL |
008 | A 12 103 837 10 | - | |
PISTON |
- | XXX XXX XXX XXXX | - | |
| PISTON WITH PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 85.00-MM = STANDARD Заменено на: A 621 030 21 17 |
- | A 62 103 010 17 | - | |
| 034 | PISTON WITH PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 85.00-MM = STANDARD |
004 | A 62 103 021 17 | - |
| 035 | COMPRESSION RING FOR PISTON GROOVE I |
004 | A 00 103 779 16 | - |
| 036 | COMPRESSION RING FOR PISTON GROOVE II AND III |
008 | A 00 103 784 16 | - |
| 038 | PC-OIL SLOTTED RING FOR PISTON GROOVE IV |
004 | A 00 103 774 18 | - |
| 039 | PISTON PIN | 004 | A 62 103 700 20 | - |
| 040 | WIRE SNAP RING | 008 | A 00 099 425 35 | - |
| PISTON WITH PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.25-MM = REPAIR SIZE I Заменено на: A 621 030 22 17 |
- | A 62 103 011 17 | - | |
| PISTON WITH PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.25-MM = REPAIR SIZE I |
004 | A 62 103 022 17 | - | |
| COMPRESSION RING FOR PISTON GROOVE I |
004 | A 00 103 780 16 | - | |
| COMPRESSION RING FOR PISTON GROOVE II AND III |
008 | A 00 103 785 16 | - | |
| PC-OIL SLOTTED RING FOR PISTON GROOVE IV |
004 | A 00 103 775 18 | - | |
| PISTON PIN | 004 | A 62 103 700 20 | - | |
| WIRE SNAP RING | 008 | A 00 099 425 35 | - | |
| PISTON WITH PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.50-MM = REPAIR SIZE II Заменено на: A 621 030 23 17 |
- | A 62 103 012 17 | - | |
| PISTON WITH PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.50-MM = REPAIR SIZE II |
004 | A 62 103 023 17 | - | |
| COMPRESSION RING FOR PISTON GROOVE I |
004 | A 00 103 781 16 | - | |
| COMPRESSION RING FOR PISTON GROOVE II AND III |
008 | A 00 103 786 16 | - | |
| PC-OIL SLOTTED RING FOR PISTON GROOVE IV |
004 | A 00 103 776 18 | - | |
| PISTON PIN | 004 | A 62 103 700 20 | - | |
| WIRE SNAP RING | 008 | A 00 099 425 35 | - | |
| PISTON WITH PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 86.00-MM = REPAIR SIZE III Заменено на: A 621 030 24 17 |
- | A 62 103 013 17 | - | |
| PISTON WITH PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 86.00-MM = REPAIR SIZE III |
004 | A 62 103 024 17 | - | |
| COMPRESSION RING FOR PISTON GROOVE I |
004 | A 00 103 782 16 | - | |
| COMPRESSION RING FOR PISTON GROOVE II AND III |
008 | A 00 103 787 16 | - | |
| PC-OIL SLOTTED RING FOR PISTON GROOVE IV |
004 | A 00 103 777 18 | - | |
| PISTON PIN | 004 | A 62 103 700 20 | - | |
| WIRE SNAP RING | 008 | A 00 099 425 35 | - | |
| PISTON WITH PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 86.50-MM = REPAIR SIZE IV Заменено на: A 621 030 25 17 |
- | A 62 103 014 17 | - | |
| PISTON WITH PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 86.50-MM = REPAIR SIZE IV |
004 | A 62 103 025 17 | - | |
| COMPRESSION RING FOR PISTON GROOVE I |
004 | A 00 103 783 16 | - | |
| COMPRESSION RING FOR PISTON GROOVE II AND III |
008 | A 00 103 788 16 | - | |
| PC-OIL SLOTTED RING FOR PISTON GROOVE IV |
004 | A 00 103 778 18 | - | |
| PISTON PIN | 004 | A 62 103 700 20 | - | |
| WIRE SNAP RING | 008 | A 00 099 425 35 | - |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy