| №- | Наименование | К* | Номер детали | A |
|---|---|---|---|---|
CRANKSHAFT |
- | XXX XXX XXX XXXX | - | |
| CRANKSHAFT WITH FLYWHEEL, COLLAR SCREW, CRANKSHAFT BEARING AND CONNECTING ROD BEARING SHELLS, MAKE LAUCHERTAL OPTIONAL |
001 | A 12 103 053 01 | - | |
| CRANKSHAFT WITH FLYWHEEL, COLLAR SCREW, CRANKSHAFT BEARING AND CONNECTION ROD BEARING SHELLS, MAKE GLYCO OPTIONAL |
001 | A 12 103 054 01 | - | |
| CRANKSHAFT WITH COUNTERWEIGHT AND FLYWHEEL Заменено на: A 121 030 35 01 |
- | A 12 103 055 01 | - | |
| 001 | CRANKSHAFT WITH COUNTERWEIGHT AND FLYWHEEL |
001 | A 12 103 035 01 | - |
| 002 | SPACER RING, 5.45-MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 | A 18 003 100 52 | - |
| SPACER RING, 5.60-MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 | A 18 003 101 52 | - | |
| SPACER RING, 5.75-MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 | A 18 003 102 52 | - | |
| SPACER RING, 5.90-MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 | A 18 003 103 52 | - | |
| SPACER RING, 6.05-MM THICK OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT |
001 | A 18 003 104 52 | - | |
| 003 | WOODRUFF KEY 5X7,5 DIN 6888 |
001 | - | |
| CRANKSHAFT GEAR ON CRANKSHAFT, FRONT Заменено на: A 180 052 02 03 |
- | A 12 205 201 03 | - | |
| 004 | CRANKSHAFT GEAR ON CRANKSHAFT, FRONT |
001 | A 18 005 202 03 | - |
| 005 | OIL SLINGER RING ON CRANKSHAFT, FRONT |
001 | A 18 003 104 25 | - |
| 05a | COUNTERWEIGHT | 001 | A 12 103 103 07 | - |
| 05b | SPACER RING FOR CRANKSHAFT, OIL SLINGER RING |
001 | A 12 103 100 51 | - |
| 006 | CYLINDRICAL PIN 8 H 8 X 8 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT |
001 | - | |
| 007 | CYLINDRICAL PIN 8 H 8 X 16 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT |
001 | - | |
| 008 | FLYWHEEL WITH RING GEAR | 001 | A 12 103 008 05 | - |
| 009 | STARTER RING GEAR, 108 TEETH |
001 | A 12 103 200 05 | - |
| 010 | EXPANDING SCREW FOR FLYWHEEL AT CRANKSHAFT |
006 | A 12 103 106 71 | - |
| 011 | CYLINDRICAL PIN 10 H 8 X 18 DIN 7 FOR FLYWHEEL AT CRANKSHAFT |
001 | - | |
| 013 | COLLAR SCREW | 001 | A 18 603 102 71 | - |
| 014 | SEALING RING AT CRANKSHAFT, FRONT |
001 | A 12 003 101 81 | - |
| 14a | ADJUSTING NEEDLE FOR ADJUSTING TOP DEAD CENTER |
001 | A 12 103 200 15 | - |
| CYLINDRICAL SCREW AM 6X8 DIN 84-4 S FOR FIXING OF ADJUSTING NEEDLE FROM ENGINE 8507471 |
001 | - | ||
| 015 | PULLEY | 001 | A 12 120 001 05 | - |
| 016 | ANNULAR GROOVED BEARING 6202 DIN 625 FOR DRIVE SHAFT AT CRANKSHAFT |
001 | - | |
| 017 | LOCKING RING FOR DRIVE SHAFT AT CRANKSHAFT |
001 | A 18 603 100 33 | - |
| 018 | SEALING RING, FABRIC 75X87X6 GL N 255 A FOR CRANKSHAFT SEALING IN CYLINDER CRANKCASE, REAR |
001 | - | |
CRANKSHAFT BEARING |
- | XXX XXX XXX XXXX | - | |
| 020 | SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. = 70-MM = STANDARD READY FOR INSTALLATION OPTIONAL |
001 | A 12 103 005 97 | - |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =70-MM = STANDARD READY FOR INSTALLATION OPTIONAL |
001 | A 62 103 000 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =70-MM = STANDARD READY FOR INSTALLATION OPTIONAL |
001 | A 12 103 010 97 | - | |
| 021 | CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 12 103 314 01 | - |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 62 103 300 01 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 12 103 319 01 | - | |
| 022 | CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 12 103 314 02 | - |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 62 103 300 02 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 12 103 319 02 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. 69.75-MM = REP.SIZE I READY FOR INSTALLATION OPTIONAL |
001 | A 12 103 006 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =69.75-MM = REP.SIZE I READY FOR INSTALLATION OPTIONAL |
001 | A 62 103 001 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =69.75-MM = REP.SIZE I READY FOR INSTALLATION OPTIONAL |
001 | A 12 103 011 97 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 12 103 315 01 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 62 103 301 01 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 12 103 320 01 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 12 103 315 02 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 62 103 301 02 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 12 103 320 02 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =69.50-MM = REP.SIZE II READY FOR INSTALLATION OPTIONAL |
001 | A 12 103 007 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =69.50-MM=REP.SIZE II READY FOR INSTALLATION OPTIONAL |
001 | A 62 103 002 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =69.50-MM = RP.SIZE II READY FOR INSTALLATION OPTIONAL |
001 | A 12 103 012 97 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 12 103 316 01 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 62 103 302 01 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, AT TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 12 103 321 02 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 12 103 316 02 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 62 103 302 02 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 12 103 321 02 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =69.25-MM=REP. SIZE III READY FOR INSTALLATION OPTIONAL |
001 | A 12 103 008 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =69.25-MM =REP. SIZE III READY FOR INSTALLATION OPTIONAL |
001 | A 62 103 003 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =69.25-MM=REP. SIZE III READY FOR INSTALLATION OPTIONAL |
001 | A 12 103 013 97 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 12 103 317 01 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 62 103 303 01 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 12 103 322 01 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 12 103 317 02 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 62 103 303 02 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 12 103 322 02 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =69.00-MM=REP.SIZE IV READY FOR INSTALLATION OPTIONAL |
001 | A 12 103 009 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. 69.00-MM=REP. SIZE IV READY FOR INSTALLATION OPTIONAL |
001 | A 62 103 004 97 | - | |
| SET OF CRANKSHAFT BEARING SHELLS, INNER DIA. =69.00-MM =REP.SIZE IV READY FOR INSTALLATION OPTIONAL |
001 | A 12 103 014 97 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 12 103 318 01 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 62 103 304 01 | - | |
| CRANKSHAFT BEARING SHELL WITH GROOVE OPTIONAL AS TOP OF 1ST AND 3RD BEARING, ON TOP AND BOTTOM OF MIDDLE BEARING (LAPPED BEARING) |
004 | A 12 103 323 01 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 12 103 318 02 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 62 103 304 02 | - | |
| CRANKSHAFT BEARING SHELL WITHOUT GROOVE OPTIONAL AS BOTTOM OF 1ST AND 3RD BEARING |
002 | A 12 103 323 02 | - | |
CONNECTING ROD |
- | XXX XXX XXX XXXX | - | |
| 025 | CONNECTING ROD | 004 | A 12 103 015 20 | - |
| 026 | CONNECTING BUSHING | 004 | A 18 603 807 50 | - |
| 027 | CONNECTING SCREW | 008 | A 12 103 803 71 | - |
| 028 | NUT | 008 | A 18 203 800 72 | - |
| CONNECTING BUSHING, OUTER DIA. = 28.5-MM REPAIRS |
004 | A 18 603 808 50 | - | |
| CONNECTING ROD BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL Заменено на: A 121 038 28 10 |
- | A 12 103 828 11 | - | |
| 029 | CONNECTING ROD BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 828 10 | - |
| CONNECTING ROD BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL Заменено на: A 121 038 07 10 |
- | A 12 103 807 11 | - | |
| CONNECTING ROD BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 807 10 | - | |
| CONNECTING ROD BEARING SHELL STANDARD INNER DIA. 52.00 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 833 10 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL Заменено на: A 121 038 29 10 |
- | A 12 103 829 11 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZ E I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 829 10 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZ E I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL Заменено на: A 121 038 08 10 |
- | A 12 103 808 11 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 808 10 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE I, INNER DIA. 51.75 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 834 10 | - | |
| CONNECTING ROD BEARING SHELL, REPAIR SIZE II, INNER DIA. 51.50-MM Заменено на: A 121 038 30 10 |
- | A 12 103 830 11 | - | |
| CONNECTING ROD BEARING SHELL, REPAIR SIZE II, INNER DIA. 51.50-MM OPTIONAL WITH 121 038 09 10/35 10 |
008 | A 12 103 830 10 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE II, INNER DIA. 51.50 MM READY FOR INSTALLATION OPTIONAL WITH 121 038 30 10 Заменено на: A 121 038 09 10 |
- | A 12 103 809 11 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE II, INNER DIA. 51.50 MM READY FOR INSTALLATION OPTIONAL WITH 121 038 30 10 |
008 | A 12 103 809 10 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE II, INNER DIA. 51.50 MM READY FOR INSTALLATION OPTIONAL WITH 121 038 30 10 |
008 | A 12 103 835 10 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION Заменено на: A 121 038 31 10 |
- | A 12 103 831 11 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 831 10 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION OPTIONAL Заменено на: A 121 038 10 10 |
- | A 12 103 810 11 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 810 10 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE III, INNER DIA. 51.25 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 836 10 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE IV, INNER DIA. 51.00 MM READY FOR INSTALLATION Заменено на: A 121 038 32 10 |
- | A 12 103 832 11 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE IV, INNER DIA. 51.00 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 832 10 | - | |
| CONNECTING ROD BEARING REPAIR SIZE IV, INNER DIA. 51.00 MM READY FOR INSTALLATION OPTIONAL Заменено на: A 121 038 11 10 |
- | A 12 103 811 11 | - | |
| CONNECTING ROD BEARING REPAIR SIZE IV, INNER DIA. 51.00 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 811 10 | - | |
| CONNECTING ROD BEARING SHELL REPAIR SIZE IV, INNER DIA. 51.00 MM READY FOR INSTALLATION OPTIONAL |
008 | A 12 103 837 10 | - | |
PISTONS |
- | XXX XXX XXX XXXX | - | |
| 034 | PISTON WITH PIN AND RINGS, CYLINDER DIA. 85.00-MM = STANDARD |
004 | A 12 103 018 17 | - |
| 035 | COMPRESSION RING PISTON GROOVE I |
004 | A 00 103 738 16 | - |
| 036 | TAPERED COMPRESSION PISTON RING PISTON GROOVE II |
004 | A 00 103 743 16 | - |
| 037 | NOVIX STEPPED RING PISTON GROOVE III |
004 | A 00 003 700 17 | - |
| 038 | NOVIX-SLOTTED RING PISTON GROOVE IV |
004 | A 00 003 729 18 | - |
| REPLACED BY D 25X18X72 DIN 73121 K |
- | A 12 103 700 20 | - | |
| 039 | PISTON PIN D 25 X 18 X 72 DIN 73121 K |
004 | - | |
| 040 | WIRE SNAP RING A 25 DIN 73123 |
008 | - | |
| PISTON WITH PIN AND RINGS, CYLINDER DIA. 85.25-MM = REP. SIZE I |
004 | A 12 103 003 17 | - | |
| COMPRESSION RING PISTON GROOVE I |
004 | A 00 103 739 16 | - | |
| TAPERED COMPRESSION PISTON RING PISTON GROOVE II |
004 | A 00 103 744 16 | - | |
| NOVIX STEPPED RING PISTON GROOVE III |
004 | A 00 003 711 17 | - | |
| NOVIX SLOTTED RING PISTON GROOVE IV |
004 | A 00 003 769 18 | - | |
| PISTON RING D 25 X 18 X 72 DIN 73121-K |
004 | - | ||
| WIRE SNAP RING A 25 DIN 73123 |
008 | - | ||
| PISTON WITH PIN AND RINGS, CYLINDER DIA. 85.50-MM = REP. SIZE II |
004 | A 12 103 004 17 | - | |
| COMPRESSION RING PISTON GROOVE I |
004 | A 00 103 740 16 | - | |
| TAPERED COMPRESSION PISTON RING PISTON GROOVE II |
004 | A 00 103 745 16 | - | |
| NOVIX STEPPED RING PISTON GROOVE III |
004 | A 00 003 701 17 | - | |
| NOVIX SLOTTED RING PISTON GROOVE IV |
004 | A 00 003 736 18 | - | |
| PISTON PIN D 25 X 18 X 72 DIN 73121 - K |
004 | - | ||
| WIRE SNAP RING A 25 DIN 73123 |
008 | - | ||
| PISTON WITH PIN AND RINGS, CYLINDER DIA. 86.00-MM = REP. SIZE III |
004 | A 12 103 005 17 | - | |
| COMPRESSION RING PISTON GROOVE I |
004 | A 00 103 741 16 | - | |
| TAPERED COMPRESSION PISTON RING PISTON GROOVE II |
004 | A 00 103 746 16 | - | |
| NOVIX STEPPED RING PISTON GROOVE III |
004 | A 00 003 702 17 | - | |
| NOVIX SLOTTED RING PISTON GROOVE IV |
004 | A 00 003 737 18 | - | |
| PISTON PIN D 25 X 18 X 72 DIN 73121 - K |
004 | - | ||
| WIRE SNAP RING A 25 DIN 73123 |
008 | - | ||
| PISTON WITH PIN AND RINGS, CYLINDER DIA. 86.5-MM = REP. SIZE IV |
004 | A 12 103 006 17 | - | |
| COMPRESSION RING PISTON GROOVE I |
004 | A 00 103 742 16 | - | |
| TAPERED COMPRESSION PISTON RING PISTON GROOVE II |
004 | A 00 103 747 16 | - | |
| NOVIX STEPPED RING PISTON GROOVE III |
004 | A 00 003 703 17 | - | |
| NOVIX SLOTTED RING PISTON GROOVE IV |
004 | A 00 003 738 18 | - | |
| PISTON PIN D 25 X 18 X 72 DIN 73121 -K |
004 | - | ||
| WIRE SNAP RING A 25 DIN 73123 |
008 | - |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy