CONTROL

EPC / Mercedes / 1 / FG / FG 180.010 / 30 / 018
‹ ›

№- Nazwa I* Numer części A

CONTROL 		- XXX XXX XXX XXXX -
ACCELERATOR PEDAL
Zastąpiono przez: A  180 301 10 01 		- A 18 030 104 01  -
001 ACCELERATOR PEDAL 001 A 18 030 110 01  -
01a ACCELERATOR PEDAL
12 MM DIA. OF HOLE 		001 A 18 030 106 01  -
MOUNTING
FOR ACCELERATOR PEDAL
Zastąpiono przez: A  180 301 00 18 		- A 18 330 100 18  -
002 MOUNTING
FOR ACCELERATOR PEDAL 		002 A 18 030 100 18  -
02a MOUNTING
FOR ACCELERATOR PEDAL 		002 A 12 130 100 18  -
003 HEX.-HD. SCREW
M 6X20 DIN 931-8 G FOR MOUNTING AT FRONT WALL 		004 -
004 SPRING WASHER
B 6 DIN 137 FOR MOUNTING AT FRONT WALL 		004 -
SPRING WASHER
A 6 DIN 137 FOR MOUNTING AT FRONT WALL 		004 -
LENS-HD. SCREW
AM 6X15 DIN 7985-4 S FOR MOUNTING AT FRONT WALL 		004 -
04a CLAMP WITH
SPRING STOP NUT 		004 A 00 099 027 91  -
005 RUBBER GROMMER
FOR ACCELERATOR PEDAL THROUGH FRONT WALL 		001 A 18 399 700 81  -
006 RELEASE SPRING
FOR ACCELERATOR PEDAL 		001 A 18 099 317 10  -
RELEASES SPRING
FOR ACCELERATOR PEDAL 		001 A 12 199 300 10  -
06a LEVER
FOR RELEASE SPRING 		001 A 18 030 200 14  -
007 CONTROL SHAFT 001 A 18 030 009 20  -
07a CONTROL SHAFT 001 A 18 030 010 20  -
008 FIXING BOLT
FOR ACCELERATOR PEDAL AT CONTROL SHAFT 		001 A 18 099 000 17  -
009 HEX. NUT
M 6 DIN 934-5 S FOR ACCELERATOR PEDAL AT CONTROL SHAFT 		001 -
010 LOCKING RING
G10X1,2 N 55 E FOR CONTROL SHAFT AT MOUNTING 		001 -
011 PULL ROD 001 A 18 030 106 15  -
BALL SOCKET
WITH SNAP RING A 8 DIN 71805 UP TO CHASSIS 7505362 		001 -
012 BALL SOCKET
WITH SNAP RING FROM CHASSIS 7505363 		001 A 12 730 000 86  -
12a SNAP RING
R 8 DIN 71805 		001 -
013 HEX. NUT
M 5 DIN 934-5 S 		001 -
014 DAMPER RING
FOR PULL ROD AT CONTROL LEVER 		001 A 18 030 100 97  -
015 WASHER
8,4 DIN 125 FOR PULL ROD AT CONTROL LEVER UP TO CHASSIS 6508100 		002 -
016 COTTER PIN
2X15 DIN 94 FOR PULL ROD AT CONTROL LEVER UP TO CHASSIS 6508100 		001 -
CHOKE CABLE WITHOUT KNOB
WIRE 1, 180 MM LONG
Zastąpiono przez: A  180 300 18 30 		- A 18 030 007 30  -
017 CHOKE CABLE WITHOUT KNOB
WIRE 1, 180 MM LONG SHORTEN LENGTH AS REQUIRED 		001 A 18 030 018 30  -
018 SPRING STEEL
WIRE 875-MM LONG III 1,5 DIN 2076 ORDER BY THE METER 		001 -
018 SPRING STEEL
WIRE 680-MM LONG III 1,5 DIN 2076 ORDER BY THE METER 		001 -
019 WIRE SPIRAL 775 MM LONG
ORDER BY THE METER 		001 A 00 098 801 72  -
019 WIRE SPIRAL 610 MM LONG
ORDER BY THE METER 		001 A 00 098 801 72  -
020 INSULATING HOSE
740-MM LONG B 5X6,2 SW DIN 40621 ORDER BY THE METER 		001 -
020 INSULATING HOSE
600-MM LONG B 5X6,2 SW DIN 40621 ORDER BY THE METER 		001 -
021 FELT RING
FOR CHOKE CABLE AT INSTRUMENT PANEL 		001 A 00 099 720 40  -
022 KNOB
FOR CHOKE CABLE AT INSTRUMENT PANEL 		001 A 12 030 204 01  -
023 WIRE CABLE,
IGNITION TIMING UP TO CHASSIS 7504707 		001 A 18 030 000 32  -
WIRE CABLE,
IGNITION TIMING UP TO CHASSIS 7504707 		001 A 18 030 001 32  -
024 RUBBER GROMMET
FOR WIRE CABLE THROUGH FRONT WALL UP TO CHASSIS 7504707 		002 A 00 099 718 81  -
LINE BRACKET
5X0,3X135 N 286 FOR IGNITION TIMING AT HEATING WATER HOSE UP TO CHASSIS 7504707 		001 -
026 RUBBER BUSHING
FOR CHOKE CABLE AT CARBURETOR 		002 A 18 099 709 81  -
027 ADJUSTING NUT
FOR CHOKE CABLE AT CARBURETOR 		001 A 18 030 200 72  -
Aby dowiedzieć się, gdzie kupić przedmiot lub jego odpowiednika, kliknij na numerze katalogowym.

Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy
Region: EU | GB | USA