ELECTRICAL EQUIPMENT AT ENGINE

EPC / Mercedes / 1 / FG / FG 121.011 / 15 / 008
‹ ›

№- Nazwa I* Numer części A

STARTER MOTOR 		- XXX XXX XXX XXXX -
001 STARTER MOTOR
WITH PUSH BUTTON OPERATION 		001 A 00 015 177 01  -
STARTER MOTOR
WITH PUSH BUTTON OPERATION 		001 A 00 015 183 01  -
002 ROLLER FREEWHEEL 001 A 00 015 120 13  -
003 SOLENOID SWITCH STARTER 001 A 00 015 210 11  -
004 SET OF CARBON BRUSHES
4 PIECES 		001 A 00 015 114 14  -
005 PRESSURE SPRING
FOR CARBON BRUSH 		004 A 00 015 105 93  -
006 BEARING BUSHING
IN DRIVE BEARING 		001 A 00 015 107 50  -
007 BEARING BUSHING
IN COMMUTATOR BEARING 		001 A 00 015 108 50  -
008 INTERMEDIATE FLANGE
FOR STARTER MOTOR AT CLUTCH HOUSING 		001 A 12 015 100 12  -
009 HEX. -HD. SCREW
M 12X80 DIN 931-8 G FOR STARTER MOTOR AT CLUTCH HOUSING 		002 -
010 WASHER
13 DIN 433 FOR STARTER MOTOR AT CLUTCH HOUSING 		002 -
011 LOCK WASHER
B 12 DIN 127 FOR STARTER MOTOR AT CLUTCH HOUSING 		002 -
012 HEX. NUT
M 12 DIN 934-5 S FOR STARTER MOTOR AT CLUTCH HOUSING 		002 -

GENERATOR IN CASE OF INSTALLATION OF A 300 W GENERATOR AND PARTS WITH INTERFERENCE SUPPRESSION SEE GROUP 54 (RADIO COMMU 		- XXX XXX XXX XXXX -
GENERATOR
MARK: RED POINT UP TO ENGINE 6500103 		001 A 00 015 425 02  -
013 GENERATOR
MARK: YELLOW POINT FROM ENGINE 6500104 		001 A 00 015 448 02  -
014 SET OF CARBON BRUSHES
2 PIECES 		001 A 00 015 427 14  -
015 PRESSURE SPRING
FOR CARBON BRUSH 		002 A 00 015 406 93  -
016 THREE -
ELEMENT VOLTAGE REGULATOR SEE ALSO GROUP 54 		001 A 00 015 455 06  -
017 PULLEY
OPTIONAL FOR GENERATOR 		001 A 18 015 507 15  -
PULLEY
OPTIONAL FOR GENERATOR 		001 A 18 015 508 15  -
018 WOODRUFF KEY
3X5 DIN 6888 FOR PULLEY AT GENERATOR HAS TO BE DELIVERED WITH GENERATOR 		001 -
019 LOCK WASHER
B 12 DIN 127 FOR PULLEY AT GENERATOR HAS TO BE DELIVERED WITH GENERATOR 		001 -
020 HEX. NUT
M 12X1,5 DIN 936-5 S FOR PULLEY AT GENERATOR HAS TO BE DELIVERED WITH GENERATOR 		001 -
021 SUPPORT
FOR GENERATOR 		001 A 12 115 508 35  -
SUPPORT
FOR GENERATOR 		001 A 12 115 503 35  -
LOCK WASHER
B 8 DIN 127 FOR SUPPORT AT CYLINDER CRANKCASE UP TO ENGINE 6500522 		002 -
HEX. NUT
M 8 DIN 934-5 S FOR SUPPORT AT CYLINDER CRANKCASE UP TO ENGINE 6500522 		002 -
022 LOCK WASHER
B 10 DIN 127 FOR SUPPORT AT CYLINDER CRANKCASE FROM ENGINE 6500523 		002 -
023 HEX. NUT
M 10 DIN 934-5 S FOR SUPPORT AT CYLINDER CRANKCASE FROM ENGINE 6500523 		002 -

Zastąpiono przez: A  121 150 03 32 		- A 18 015 000 32  -

Zastąpiono przez: A  121 150 03 32 		- A 12 115 000 32  -
GROUND CABLE
FOR SUPPORT AT GENERATOR
Zastąpiono przez: A  121 150 03 32 		- A 12 115 001 32  -
024 GROUND CABLE
FOR SUPPORT AT GENERATOR 		001 A 12 115 003 32  -
025 HEX. -HD. SCREW
M 8X35 DIN 931-8 G FOR GENERATOR AT SUPPORT 		001 -
HEX. -HD. SCREW
M 8X40 DIN 931-8 G FOR GENERATOR AT SUPPORT 		002 -
SLEEVE
FOR GENERATOR AT SUPPORT UP TO ENGINE 6500264 		001 A 18 099 106 40  -
RUBBER WASHER
FOR GENERATOR AT SUPPORT UP TO ENGINE 6500264 		002 A 12 115 500 81  -
WASHER
FOR GENERATOR AT SUPPORT UP TO ENGINE 6500264 		002 A 12 015 500 82  -
026 INTERMEDIATE WASHER
FOR GENERATOR AT SUPPORT FROM ENGINE 6500265 		002 A 12 115 500 76  -
SLEEVE
FOR GENERATOR AT SUPPORT, FRONT 		001 A 12 199 104 40  -
RUBBER WASHER
FOR GENERATOR AT SUPPORT, FRONT 		002 A 12 115 500 81  -
WASHER
FOR GENERATOR AT SUPPORT, FRONT 		002 A 12 115 500 82  -
INTERMEDIATE WASHER
FOR GENERATOR AT SUPPORT, REAR 		002 A 12 115 501 76  -
029 LOCK WASHER
B 8 DIN 127 FOR GENERATOR AT SUPPORT 		001 -
030 HEX. NUT
M 8 DIN 934-5 S FOR GENERATOR AT SUPPORT 		001 -
031 HEX. -HD. SCREW
M 8X60 DIN 931-8 G FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001 -
032 SLEEVE
FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001 A 18 099 106 40  -
033 RUBBER WASHER
FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		002 A 12 015 500 81  -
034 WASHER
FOR GENERATOR SUSPENSION, RUBBER MOUNTED FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		002 A 12 015 500 82  -
035 WASHER
FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001 A 12 199 001 40  -
036 SPACER SLEEVE,
25.5-MM LONG FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001 A 12 115 500 53  -
037 LOCK WASHER
B 8 DIN 127 FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001 -
038 HEX. NUT
M 8 DIN 934-5 S FOR GENERATOR AT ENGINE SUPPORT, RIGHT 		001 -
039 TIGHTENING SCREW
FOR GENERATOR ADJUSTMENT 		001 A 12 115 501 23  -
040 TIGHTENING NUT
FOR GENERATOR ADJUSTMENT 		001 A 12 115 500 72  -
REPLACED BY
121 155 01 28 TOGETHER WITH 1 HEX. -HD. SCREW M 8X30 DIN 931-8 G UP TO ENGINE 7505524 		- A 12 115 500 28  -
041 CLAMPING PIECE
FOR GENERATOR ADJUSTMENT FROM ENGINE 7505525 		001 A 12 115 501 28  -
042 HEX. NUT
M 8 DIN 934-5 S FOR GENERATOR ADJUSTMENT 		001 -
SLEEVE
FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE UP TO ENGINE 6500264 		001 A 12 099 103 40  -
RUBBER WASHER
FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE UP TO ENGINE 6500264 		002 A 12 015 500 81  -
WASHER
FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE UP TO ENGINE 6500264 		002 A 12 015 500 82  -
043 INTERMEDIATE WASHER
FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE FROM ENGINE 6500265 		002 A 12 115 500 76  -
046 LOCK WASHER
B 8 DIN 127 FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE 		001 -
047 HEX. NUT
M 8 DIN 934-5 S FOR TIGHTENING SCREW WITH CLAMPIN PIECE AT CYLINDER CRANKCASE 		001 -
HEX. -HD. SCREW
M 8X40 DIN 931-8 G FOR CLAMPING PIECE AT GENERATOR UP TO ENGINE 7505524 		001 -
048 HEX. -HD. SCREW
M 8X30 DIN 931-8 G FOR CLAMPING PIECE AT GENERATOR FROM ENGINE 7505525 		001 -
049 LOCK WASHER
B 8 DIN 127 FOR CLAMPING PIECE AT GENERATOR 		001 -
HEX. NUT
M 8 DIN 934-5 S FOR CLAMPING PIECE AT GENERATOR UP TO ENGINE 7505524 		001 -
TIGHTENING SCREW
FOR GENERATOR ADJUSTMENT 		001 A 12 115 502 23  -
HEX. -HD. SCREW
M 8X60 DIN 931-8 G FOR TIGHTENING SCREW WITH CLAMPING PIECE AT WATER PUMP 		001 -
SPACER RING
FOR TIGHTENING SCREW WITH CLAMPING PIECE AT WATER PUMP 		001 A 12 115 500 51  -
INTERMEDIATE WASHER
FOR TIGHTENING SCREW WITH CLAMPING PIECE AT WATER PUMP 		002 A 12 115 501 76  -

IGNITION DISTRIBUTOR 		- XXX XXX XXX XXXX -
REPLACED BY
000 158 73 01 TOGETHER WITH 1 VACUUM PIPE 121 150 03 35 UP TO ENGINE 9501268 		- A 00 015 851 01  -
REPLACED BY
000 158 73 01 TOGETHER WITH 1 VACUUM PIPE 121 150 03 35 UP TO ENGINE 9501268 		- A 00 015 870 01  -
055 IGNITION DISTRIBUTOR
WITH COUPLING AND VACUUM ADJUSTING DEVICE INTERFERENCE-FREE FROM ENGINE 9501269 		001 A 00 015 873 01  -
REPLACED BY
000 158 074 01 TOGETHER WITH 1 VACUUM PIPE 121 150 03 35 EXPORT - SPECIAL REQUEST (DUST - PROOF DESIGN) UP TO ENGINE 950 		- A 00 015 864 01  -
REPLACED BY
000 158 074 01 TOGETHER WITH 1 VACUUM PIPE 121 150 03 35 EXPORT - SPECIAL REQUEST (DUST - PROOF DESIGN) UP TO ENGINE 950 		- A 00 015 872 01  -
IGNITION DISTRIBUTOR
WITH COUPLING AND VACUUM ADJUSTING DEVICE INTERFERENCE - FREE EXPORT - SPECIAL REQUEST (DUST - PROOF DESIGN) FROM ENGINE 		001 A 00 015 874 01  -
056 DISTRIBUTOR PLATE
WITH CARBON BRUSH 		001 A 00 015 806 02  -
057 CARBON BRUSH WITH SPRING 001 A 00 015 800 34  -
058 OILER IN HOUSING 001 A 00 015 804 89  -

Zastąpiono przez: A  000 158 07 90 		- A 00 015 803 30  -
CONTACT SET
Zastąpiono przez: A  000 158 07 90 		- A 00 015 802 32  -
059 CONTACT SET 001 A 00 015 807 90  -

Zastąpiono przez: A  000 158 15 31 		- A 00 015 806 31  -

Zastąpiono przez: A  000 158 15 31 		- A 00 015 805 31  -
DISTRIBUTOR ROTOR
WITH COUNTER WEIGHT DUST-PROOF AND INTERFERENCE-FREE
Zastąpiono przez: A  000 158 15 31 		- A 00 015 811 31  -
061 DISTRIBUTOR ROTOR
WITH COUNTER WEIGHT DUST-PROOF AND INTERFERENCE-FREE 		001 A 00 015 815 31  -
DUST PROTECTIVE COVER
EXPORT - SPECIAL REQUEST 		001 A 00 015 800 11  -
062 LEAF SPRING
FOR DISTRIBUTOR PLATE 		002 A 00 015 803 33  -
063 FIXING SHACKLE
WITHOUT NOSE 		001 A 00 015 803 40  -
064 FIXING SHACKLE WITH NOSE 001 A 00 015 804 40  -
065 CYLINDRICAL SCREW
AM 4X8 DIN 84-4 S FOR FIXING SHACKLE WITH LEAF SPRING AT IGNITION DISTRIBUTOR 		002 -
066 LOCK WASHER
B 4 DIN 127 FOR FIXING SHACKLE WITH LEAF SPRING AT IGNITION DISTRIBUTOR 		002 -
CONDENSER AT HOUSING
UP TO ENGINE 9501268 		001 A 00 015 611 01  -
067 CONDENSER AT HOUSING
FROM ENGINE 9501269 		001 A 00 015 649 01  -
068 FIXING CLAMP
FOR CONDENSER AT IGNITION DISTRIBUTOR FROM ENGINE 9501269 		001 A 00 015 806 40  -
CYLINDRICAL SCREW
AM 4X5 DIN 84-5 S FOR CONDENSER AT IGNITION DISTRIBUTOR 		002 -
LOCK WASHER
B 4 DIN 127 FOR CONDENSER AT IGNITION DISTRIBUTOR 		002 -
VACUUM ADJUSTING DEVICE
UP TO ENGINE 9501268 		001 A 00 015 804 18  -
070 VACUUM ADJUSTING DEVICE
FROM ENGINE 9501269 		001 A 00 015 805 18  -
071 CYLINDRICAL SCREW
AM 4X5 DIN 84-5 S FOR VACUUM ADJUSTING DEVICE AT IGNITION DISTRIBUTOR 		002 -
072 LOCK WASHER
B 4 DIN 127 FOR VACUUM ADJUSTING DEVICE AT IGNITION DISTRIBUTOR 		002 -
COUPLING
ON SHAFT UP TO ENGINE 9501268 		001 A 00 015 803 09  -
073 COUPLING
ON SHAFT FROM ENGINE 9501269 		001 A 00 015 805 09  -
074 FIBER WASHER
FOR COUPLING AT IGNITION DISTRIBUTOR 		002 A 00 015 801 76  -
075 SHIM 0.1 MM THICK
FOR COUPLING AT IGNITION DISTRIBUTOR OPTIONAL 		NB A 00 015 800 52  -
SHIM 0.2 MM THICK
FOR COUPLING AT IGNITION DISTRIBUTOR OPTIONAL 		NB A 00 015 804 52  -
PIN
FOR COUPLING AT IGNITION DISTRIBUTOR UP TO ENGINE 9501268 		001 A 00 015 804 74  -
076 PIN
FOR COUPLING AT IGNITION DISTRIBUTOR FROM ENGINE 9501269 		001 A 00 015 807 74  -
76a SNAP RING
FOR COUPLING AT IGNITION DISTRIBUTOR FROM ENGINE 9501269 		001 A 00 015 802 77  -
077 THREADED BUSHING 001 A 00 015 800 59  -
078 SEALING RING 001 A 00 015 802 60  -
REPLACED BY
121 150 02 07 TOGETHER WITH 1 INTERMEDIATE RING 121 158 00 51 1 HEX. -HD. SOCKET SCREW M 8X45 DIN 912-8 G 1 WASHER 8,4 D 		- A 18 015 009 07  -

Zastąpiono przez: A  121 150 02 07 		- A 12 115 000 07  -
BEARING, IGNITION
Zastąpiono przez: A  121 150 02 07 		- A 12 115 001 07  -
080 BEARING, IGNITION
DISTRIBUTOR FROM ENGINE 6500026 		001 A 12 115 002 07  -
081 ADJUSTING LEVER
WITH ANGLE UP TO ENGINE 8511499 		001 A 18 015 001 24  -
81a ADJUSTING LEVER
FROM ENGINE 8511500 		001 A 18 015 003 24  -
082 HEX. -HD. SOCKET SCREW
M 6X25 DIN 912-8 G 		001 -
82a ADJUSTING ECCENTRIC
FROM ENGINE 8511500 		001 A 18 015 002 24  -
SPRING WASHER
B 6 DIN 137 FOR ADJUSTER LEVER AT ADJUSTING EXCENTRIC FROM ENGINE 8511500 		001 -
HEX. -HD. SCREW
M 6X8 DIN 933-8 G FOR ADJUSTER LEVER AT ADJUSTING EXCENTRIC FROM ENGINE 8511500 		001 -
083 HEX. -HD. SCREW
M 5X30 S DIN 931-8G FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8511499 		001 -
084 WASHER
5,3 DIN 125 FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8511499 		001 -
085 HELICAL SPRING
FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8511499 		001 A 13 693 308 01  -
086 HEX. NUT
M 5 DIN 934-5 S FOR ADJUSTING LEVER AT BEARING UP TO ENGINE 8511499 		001 -
087 COTTER PIN
1 X 12 DIN 94 FOR ADJUSTING LEVER AT BEARING 		001 -
088 HEX. -HD. SCREW WITH PIN
AM 6X12 DIN 561-5 S FOR FIXING OF IGNITION DISTRIBUTOR UP TO ENGINE 8511499 		001 -
089 PRESSURE SPRING
FOR IGNITION TIMING UP TO ENGINE 8511499 		001 A 18 699 324 01  -
ADJUSTING SCREW
FOR IGNITION TIMING UP TO ENGINE 7506870 		001 A 18 615 800 70  -
HEX. NUT
M 10X1 DIN 936-5 S FOR IGNITION TIMING UP TO ENGINE 7506870 		001 -
RUBBER SLEEVE
FOR IGNITION TIMING UP TO ENGINE 7506870 		001 A 18 615 800 83  -
DAMPING RUBBER
FOR IGNITION TIMING UP TO ENGINE 7506870 		001 A 18 615 801 83  -
SLEEVE
FOR IGNITION TIMING UP TO ENGINE 7506870 		001 A 18 615 800 51  -
CLAMPING CHUCK
FOR WIRE CABLE, IGNITION TIMING UP TO ENGINE 7506870 		001 A 19 815 000 29  -
090 ADJUSTING SCREW
FOR ADJUSTING LEVER AT BEARING FROM ENGINE 7506871 UP TO 8511499 		001 A 12 115 000 84  -
091 KNURLED NUT
FOR ADJUSTING SCREW FROM ENGINE 7506871 UP TO 8511499 		001 A 12 199 000 57  -
094 WASHER
FOR ADJUSTING SCREW FROM ENGINE 7506871 UP TO 8511499 		001 A 12 115 800 76  -
097 BEARING WITH BUSHING
FOR IGNITION DISTRIBUTOR AND OIL PUMP HOUSING 		001 A 18 015 001 07  -
098 HELICAL GEAR
FOR IGNITION DISTRIBUTOR DRIVE 		001 A 18 015 804 12  -
100 INTERMEDIATE RING
FOR BEARING, IGNITION DISTRIBUTOR, AT CYLINDER CRANKCASE FROM ENGINE 6500026 		001 A 12 115 800 51  -
101 HEX. -HD. SOCKET SCREW
M 8X45 DIN 912-8 G FOR BEARING, IGNITION DISTRIBUTOR, AT CYLINDER CRANKCASE FROM ENGINE 6500026 		001 -
102 WASHER
8,4 DIN 125 FOR BEARING, IGNITION DISTRIBUTOR, AT CYLINDER CRANKCASE FROM ENGINE 6500026 		001 -
HEX. -HD. SCREW
M 8X10 DIN 933-8 G FOR LOCKING OF THREADED BORE AT CYLINDER CRANKCASE UP TO ENGINE 6514359 		001 -
VACUUM PIPE
UP TO ENGINE 9501268 		001 A 12 115 000 35  -
104 VACUUM PIPE
FROM ENGINE 9501269 		001 A 12 115 003 35  -
105 SCREW
4 DIN 3871 		001 -
106 DOUBLE CONE RING
4 DIN 3862 		001 -
107 RUBBER HOSE 001 A 18 199 703 82  -
108 HOSE STRAP 002 A 18 199 700 90  -
109 SPRING CLAMP
FOR FUEL PIPE AND VACUUM PIPE 		002 A 18 099 305 25  -
REPLACED BY 180 993 05 25
FOR FUEL PIPE AND VACUUM PIPE
Zastąpiono przez: A  180 993 05 25 		- A 18 099 504 01  -
HEX. -HD. SCREW
M 5X10 DIN 933-8 G FOR FUEL PIPE AND VACUUM PIPE UP TO ENGINE 7522096 		001 -
LOCK WASHER
B 5 DIN 127 FOR FUEL PIPE AND VACUUM PIPE UP TO ENGINE 7522096 		001 -
HEX. NUT
M 5 DIN 934-5 S FOR FUEL PIPE AND VACUUM PIPE UP TO ENGINE 7522096 		001 -
113 SEALING RING
A 6X12 DIN 7603 A1 FOR VACUUM CONNECTION AT CARBURETOR 		001 -
114 CONNECTION FITTING
FOR VACUUM CONNECTION AT CARBURETOR 		001 A 18 115 801 37  -
114a GROUND CABLE
FROM IGNITION DISTRIBUTOR TO CYLINDER HEAD FROM ENGINE 6511911 		001 A 12 115 002 32  -

IGNITION CABLE 		- XXX XXX XXX XXXX -
IGNITION CABLE
HARNESS WITH PROTECTIVE TUBE
Zastąpiono przez: A  121 150 03 19 		- A 12 115 001 19  -
115 IGNITION CABLE
HARNESS WITH PROTECTIVE TUBE 		001 A 12 115 003 19  -
IGNITION CABLE PLUG
C DIN 72566 MAKE BOSCH OPTIONAL
Zastąpiono przez: A  000 156 15 10 		- -
116 IGNITION CABLE PLUG
MAKE BOSCH OPTIONAL 		004 A 00 015 615 10  -
IGNITION CABLE PLUG
MAKE BERU OPTIONAL 		004 A 00 015 620 10  -
117 CABLE SLEEVE 004 A 00 015 900 38  -
118 RAIN PROTECTIVE CAP
FOR IGNITION CABLE 		004 A 00 015 900 85  -
119 GROMMET
FOR PROTECTIVE TUBE 		004 A 00 099 722 81  -
119 IGNITION CABLE
FOR IGNITION COIL, DISTRIBUTOR
Zastąpiono przez: A  180 150 06 18 		- A 12 115 004 18  -
120 IGNITION CABLE
FOR IGNITION COIL, DISTRIBUTOR 		001 A 18 015 006 18  -
CABLE SLEEVE 002 A 00 015 900 38  -
RAIN PROTECTIVE CAP
FOR IGNITION CABLE 		002 A 00 015 900 85  -
PLUG FOR
INTERFERENCE SUPPRESSION MAKE BOSCH OPTIONAL SPECIAL REQUEST - FOR RADIO INSTALLATION
Zastąpiono przez: A  000 156 17 10 		- A 00 015 610 10  -
PLUG FOR
INTERFERENCE SUPPRESSION MAKE BOSCH OPTIONAL SPECIAL REQUEST - FOR RADIO INSTALLATION 		005 A 00 015 617 10  -
PLUG FOR
INTERFERENCE SUPPRESSION MAKE BERU OPTIONAL SPECIAL REQUEST - FOR RADIO INSTALLATION 		005 A 00 015 621 10  -
RUBBER CAP
SPECIAL REQUEST - FOR RADIO INSTALLATION
Zastąpiono przez: A  000 159 07 85 		- A 00 015 905 85  -
RUBBER CAP
SPECIAL REQUEST - FOR RADIO INSTALLATION 		005 A 00 015 907 85  -
121 GROMMET 002 A 15 954 600 37  -
122 CABLE TERMINAL
4X0,8 N 261 		001 -
123 CABLE TERMINAL
5X0,8 N 261 		001 -
124 LOCK WASHER
B 6 DIN 127 FOR PROTECTIVE TUBE AT CYLINDER HEAD 		002 -
125 HEX. -HD. SCREW
M 6X10 DIN 933-8 G FOR PROTECTIVE TUBE AT CYLINDER HEAD 		002 -

SPARK PLUG 		- XXX XXX XXX XXXX -
REPLACED BY 000 159 59 03
OPTIONAL
Zastąpiono przez: A  000 159 59 03 		- A 00 015 917 03  -
REPLACED BY 000 159 59 03
OPTIONAL
Zastąpiono przez: A  000 159 59 03 		- A 00 015 918 03  -
REPLACED BY 000 159 59 03
OPTIONAL
Zastąpiono przez: A  000 159 59 03 		- A 00 015 943 03  -
SPARK PLUG
OPTIONAL
Zastąpiono przez: A  000 159 59 03 		- A 00 015 946 03  -
126 SPARK PLUG
MAKE BOSCH OPTIONAL 		004 A 00 015 959 03  -
REPLACED BY 000 159 75 03
OPTIONAL
Zastąpiono przez: A  000 159 75 03 		- A 00 015 906 03  -
SPARK PLUG
OPTIONAL
Zastąpiono przez: A  000 159 75 03 		- A 00 015 916 03  -
SPARK PLUG
MAKE BERU OPTIONAL 		004 A 00 015 975 03  -
SPARK PLUG,
INTERFERENCE-FREE MAKE BOSCH OPTIONAL SPECIAL REQUEST FOR INSTALLATION OF RADIO AND 300 WATT GENERATOR 		004 A 00 015 955 03  -
SPARK PLUG,
INTERFERENCE-FREE OPTIONAL SPECIAL REQUEST FOR INSTALLATION OF RADIO AND 300 WATT GENERATOR
Zastąpiono przez: A  000 159 78 03 		- A 00 015 945 03  -
SPARK PLUG,
INTERFERENCE-FREE MAKE BERU OPTIONAL SPECIAL REQUEST FOR INSTALLATION OF RADIO AND 300 WATT GENERATOR 		004 A 00 015 978 03  -
127 SEALING RING
C 14X20 DIN 7603 ST. ASB. FOR SPARK PLUG AT CYLINDER HEAD HAS TO BE DELIVERED WITH SPARK PLUG 		004 -

IGNITION COIL 		- XXX XXX XXX XXXX -
128 IGNITION COIL
AT FRONT WALL SEE GROUP 54 		001 A 00 015 800 03  -
Aby dowiedzieć się, gdzie kupić przedmiot lub jego odpowiednika, kliknij na numerze katalogowym.

Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy
Region: EU | GB | USA