№ | Name | Ext. inf. | A* | Use of | Part number | A |
---|---|---|---|---|---|---|
wiring set for engine CGPA,CGPB,
CJLB |
CGPA,CGPB, CJLB |
|||||
wiring set for engine CGPA,CGPB,
CJLB |
CGPA,CGPB, CJLB |
|||||
- | * free cable ends * must be isolated |
|||||
1 | wiring set for engine for models with oil level sensor PR-T70+QG1,
QG2 |
PR-T70+QG1, QG2 |
1 | 03E 971 612 AN | - | |
(1) | wiring set for engine PR-T70+QG0
|
PR-T70+QG0 | 1 | 03E 971 612 AM | - | |
individual parts | ||||||
- | * corrug. tubes, t-pieces, * clips, holders, grommets, * cable ties, insulating * hose, wiring, * single wires and seals * see special catalogue: * electrical * connecting elements |
|||||
2 | not for this model | |||||
2A | clip | X | 03C 937 073 | - | ||
2B | not for this model | |||||
2C | not for this model | |||||
3 | wiring set for battery + starter |
1 | 6Y0 971 228 A | - | ||
4 | not for this model | |||||
5 | cable tie with terminal socket for bridge strength: toothed quadrant colour strip width: |
X | 1Y0 971 838 | - | ||
5 | cable tie with terminal socket for bridge strength: toothed quadrant colour strip width: |
X | 5M0 971 838 A | - | ||
6 | flat contact housing with gasket engine control unit PR-T70+QG0
|
PR-T70+QG0 | 1 | 1J0 906 379 B | - | |
(6) | flat contact housing with cap PR-T70+QG1,
QG2 |
PR-T70+QG1, QG2 |
1 | 1S0 906 379 | - | |
7 | holder for wiring harness coupling st. connector housing wiring set for engine |
1 | 6R0 971 848 | - | ||
8 | cable guide | 1 | 03E 971 824 | - | ||
9 | flat contact housing with contact locking mechanism oil pressure switch |
X | 1J0 973 081 | - | ||
10 | flat contact housing with contact locking mechanism knock sensor temperature sensor a/c compressor |
X 1 1 1 |
1J0 973 702 | 3 | ||
11 | flat contact housing with contact locking mechanism camshaft adjuster unit compl. speedometer impulse sender oil level sensor |
X 1 1 1 1 |
3D0 973 703 | 2 | ||
12 | flat contact housing with contact locking mechanism temperature sensor intake manifold |
1 | 1J0 973 704 | 3 | ||
13 | flat contact housing throttle valve positioner |
1 | 1J0 973 713 | 1 | ||
14 | flat contact housing with contact locking mechanism injection valve |
3 | 06A 973 722 | - | ||
(14) | flat contact housing with contact locking mechanism activated charcoal container with valve |
1 | 1J0 973 722 A | 5 | ||
(14) | flat contact housing activated charcoal container with valve |
1 | 3B0 973 722 A | - | ||
15 | flat contact housing with contact locking mechanism ignition coil |
1 | 4B0 973 724 | 1 | ||
16 | not for this model | |||||
17 | flat contact housing with contact locking mechanism harness for engine compartment |
1 | 1J0 973 837 | - | ||
18 | not for this model | |||||
19 | cable tie with holder for weld pin: |
X | N 906 437 01 | - | ||
20 | cable ties hole/sheet metal thickness: |
X | 3D0 971 838 N | 2 | ||
single parts whitch are not included with the parts supp- lied with the wiring harness BZG,CGPA,
CGPB |
BZG,CGPA, CGPB |
|||||
40 | cable tie with terminal socket for bridge strength: |
X | 3D0 971 838 M | - | ||
41 | cable guide connection piece ignition coil with spark plug connector use if required: |
1 | 03E 971 815 A | - | ||
- | bracket | 1 | 03E 971 858 C | - | ||
- | bracket | 1 | 03E 971 858 B | - |