Wiring set for motor and 3-pha..
| № | Name | Ext. inf. | A* | Use of | Part number | A |
|---|---|---|---|---|---|---|
| wiring set for motor and 3-phase alternator CBZB
|
CBZB | |||||
| wiring set for engine CBZB
|
CBZB | |||||
| (1) | wiring set for engine CBZB
|
CBZB | 1 | 03F 971 612 | - | |
| (1) | wiring set for engine dual clutch
gearbox+ CBZB |
dual clutch gearbox+ CBZB |
1 | 03F 971 612 A | - | |
| wiring set for engine for vehicles with start-stop CBZB
|
CBZB | |||||
| (1) | wiring set for engine for vehicles with start-stop CBZB
|
CBZB | 1 | 03F 971 612 B | - | |
| individual parts | ||||||
| - | * corrug. tubes, t-pieces, * clips, holders, grommets, * cable ties, insulating * hose, wiring, * single wires and seals * see special catalogue: * electrical * connecting elements |
|||||
| 2 | no replacement part | |||||
| 3 | no replacement part | |||||
| 2A | clamping piece | 1 | 6X0 915 138 | - | ||
| 2B | hexagon nut | 1 | N 011 006 27 | 6 | ||
| 2C | washer | 1 | N 011 557 8 | - | ||
| 4 | cable guide | X | 6Q0 971 615 G | - | ||
| 5 | cover cable guide |
1 | 6Q0 971 839 B | - | ||
| (6) | flat contact housing with contact locking mechanism engine control unit |
1 | 4E0 906 379 | - | ||
| (7) | retainer, swivel for cable: |
1 | N 107 477 01 | - | ||
| (7) | retainer, swivel | 1 | N 106 757 01 | - | ||
| (8) | cable guide | 1 | 03F 971 824 | - | ||
| (9) | flat contact housing with contact locking mechanism oil pressure switch |
X | 1J0 973 081 | - | ||
| (10) | flat contact housing with contact locking mechanism fuel pump |
1 | 4F0 973 702 | - | ||
| 10 | flat contact housing with contact locking mechanism knock sensor temperature sensor |
X 1 1 |
1J0 973 702 | 3 | ||
| (10) | flat contact housing with contact locking mechanism coolant pump |
1 | 1J0 973 702 | 3 | ||
| 11 | flat contact housing with contact locking mechanism camshaft adjuster unit compl. impulse sender oil level sensor |
X 1 1 |
3D0 973 703 | 2 | ||
| (11) | flat contact housing with contact locking mechanism double ignition coil |
1 | 1J0 973 703 B | - | ||
| (11) | flat contact housing with contact locking mechanism double ignition coil |
1 | 8K0 973 703 C | - | ||
| 12 | flat contact housing with contact locking mechanism intake manifold throttle valve |
X 1 1 |
1J0 973 704 | 3 | ||
| 13 | flat contact housing throttle valve positioner exhaust gas recirculation use if required: |
X 1 1 X |
1J0 973 713 | 1 | ||
| (13) | flat contact housing air quality sensor |
1 | 5N1 973 206 | - | ||
| 14 | flat contact housing with contact locking mechanism injection valve |
4 | 07P 973 702 | - | ||
| (14) | flat contact housing with contact locking mechanism coolant hose with valve |
1 | 1J0 973 722 | 3 | ||
| (14) | flat contact housing with contact locking mechanism activated charcoal container with valve |
1 | 1J0 973 722 | 3 | ||
| 15 | flat contact housing ignition coil |
1 | 1J0 973 724 | 1 | ||
| (15) | flat contact housing with contact locking mechanism speed sender |
1 | 1J0 973 703 B | - | ||
| (15) | flat contact housing with contact locking mechanism speed sender |
1 | 8K0 973 703 C | - | ||
| 16 | flat connector housing with contact locking mechanism pressure sensor |
3 | 4D0 971 993 | - | ||
| 17 | flat contact housing with contact locking mechanism harness for engine compartment |
1 | 1J0 973 837 | - | ||
| 18 | cable holder coolant hose |
X | N 105 074 01 | - | ||
| 19 | cable tie with holder for weld pin: |
X | N 906 437 01 | - | ||
| 20 | cable ties hole/sheet metal thickness: |
X | 3D0 971 838 N | 2 | ||
| (20) | cable tie with holder for weld pin: |
X | 3D0 971 838 A | - | ||
| (20) | cable ties hole/sheet metal thickness: toothed quadrant high temperature resistant |
X | 3W0 971 838 | 1 | ||
| single parts whitch are not included with the parts supp- lied with the wiring harness |
||||||
| 40 | double binder cable tie with bracket for hole/sheet metal thickness: |
X | 8E0 971 818 | - | ||
| (7) | clip | 2 | 03C 937 073 | - | ||
| (18) | cable holder | 1 | 6Q0 971 842 | - | ||
| (18) | cable holder alternator use if required: |
1 X |
N 020 622 7 | - | ||
| (7) | holder for wiring harness coupling st. connector housing wiring set for engine |
1 | 6R0 971 848 | - | ||
| (7) | retaining plate engine bay dual clutch
gearbox+ |
dual clutch gearbox+ |
1 | 6R0 971 858 B | - | |
| (7) | retaining plate | 1 | 6R0 971 858 E | - | ||
| (41) | bracket for connector housing connection piece flat contact housing for lambda probe hexagon collar nut |
1 2 |
1J0 971 830 N | - |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy