Wiring set for engine.
| № | Name | Ext. inf. | A* | Use of | Part number | A |
|---|---|---|---|---|---|---|
| wiring set for engine BZG,CGPA,
CGPB |
BZG,CGPA, CGPB |
|||||
| wiring set for engine BZG,CGPA,
CGPB |
BZG,CGPA, CGPB |
|||||
| - | * free cable ends * must be isolated ------------------------------ |
|||||
| 1 | wiring set for motor and 3-phase alternator D >> - 22.03.2010 |
1 | 03E 971 612 AD | - | ||
| 1 | wiring set for motor and 3-phase alternator D >> - 08.11.2010 |
1 | 03E 971 612 AD | - | ||
| (1) | wiring set for engine for models with oil level sensor CGPA,CGPB
|
CGPA,CGPB | 1 | 03E 971 612 AJ | - | |
| individual parts BZG,CGPA,
CGPB |
BZG,CGPA, CGPB |
|||||
| - | * corrug. tubes, t-pieces, * clips, holders, grommets, * cable ties, insulating * hose, wiring, * single wires and seals * see special catalogue: * electrical * connecting elements |
|||||
| 2 | not for this model | |||||
| 2A | clip | X | 03C 937 073 | - | ||
| 2B | not for this model | |||||
| 2C | not for this model | |||||
| 3 | wiring set for battery + starter |
1 | 6Y0 971 228 A | - | ||
| 4 | not for this model | |||||
| 5 | cable tie with terminal socket for bridge strength: toothed quadrant colour strip width: |
X | 1Y0 971 838 | - | ||
| 6 | flat contact housing with gasket engine control unit |
1 | 1J0 906 379 B | - | ||
| 7 | cable holder coupling element harness for engine compartment D >> - 01.02.2009 |
1 | 6Q0 971 848 L | - | ||
| (7) | holder for wiring harness coupling st. connector housing wiring set for engine D - 02.02.2009>> |
1 | 6R0 971 848 | - | ||
| 8 | cable guide | 1 | 03E 971 824 | - | ||
| 9 | flat contact housing with contact locking mechanism oil pressure switch |
X | 1J0 973 081 | - | ||
| 10 | flat contact housing with contact locking mechanism knock sensor temperature sensor a/c compressor |
X 1 1 1 |
1J0 973 702 | 3 | ||
| 11 | flat contact housing with contact locking mechanism camshaft adjuster unit compl. speedometer impulse sender oil level sensor |
X 1 1 1 1 |
3D0 973 703 | 2 | ||
| 12 | flat contact housing with contact locking mechanism temperature sensor intake manifold |
1 | 1J0 973 704 | 3 | ||
| 13 | flat contact housing throttle valve positioner |
1 | 1J0 973 713 | 1 | ||
| 14 | flat contact housing with contact locking mechanism injection valve |
3 | 06A 973 722 | - | ||
| (14) | flat contact housing with contact locking mechanism activated charcoal container with valve |
1 | 1J0 973 722 A | 5 | ||
| (14) | flat contact housing activated charcoal container with valve |
1 | 3B0 973 722 A | - | ||
| 15 | flat contact housing ignition coil |
3 | 1J0 973 724 | 1 | ||
| 16 | not for this model | |||||
| 17 | flat contact housing with contact locking mechanism harness for engine compartment |
1 | 1J0 973 837 | - | ||
| 18 | not for this model | |||||
| 19 | cable tie with holder for weld pin: |
X | N 906 437 01 | - | ||
| 20 | cable ties hole/sheet metal thickness: |
X | 3D0 971 838 N | 2 | ||
| single parts whitch are not included with the parts supp- lied with the wiring harness BZG,CGPA,
CGPB |
BZG,CGPA, CGPB |
|||||
| 40 | cable tie with terminal socket for bridge strength: |
X | 3D0 971 838 E | - | ||
| 41 | cable guide connection piece ignition coil with spark plug connector use if required: |
1 | 03E 971 815 A | - | ||
| - | clip | X | 03C 937 073 | - | ||
| - | bracket | 1 | 03E 971 858 C | - | ||
| - | bracket | 1 | 03E 971 858 B | - |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy