EXHAUST SYSTEM USED ON FOUR-CYLINDER GASOLINE VEHICLES
| №- | Name | A* | Part number |
|---|---|---|---|
| 010 | EXHAUST GAS LINE CATALYST,FRONT PART IS ONLY OR ALSO SUPPLIED AS RECONDITIONED PART |
001 | A 246 490 24 10 |
| 030 | MULTI-HOLE SEAL BETWEEN EXHAUST MANIFOLD ANDCYLINDER HEAD |
001 | A 271 142 07 80 |
| 030 | MULTI-HOLE SEAL BETWEEN EXHAUST MANIFOLD ANDCYLINDER HEAD |
001 | A 271 142 07 80 |
| 040 | HEXAGON NUT W FLANGE EXHAUST SYSTEM AT TURBOCHARGER |
003 | A 002 990 39 50 |
| 060 | SCREW W RND. HEXAL. HEAD BRACKET TO EXHAUST MANIFOLD M8X15 |
002 | A 002 990 43 03 |
| 070 | BRACKET AT OIL PAN |
001 | A 246 492 02 41 |
| 080 | HEXALOBULAR BOLT BRACKET TO OIL PAN M8X16 |
002 | N 000000 003853 |
| 090 | SCREW W RND. HEXAL. HEAD BRACKET TO EXHAUST PIPE M8X15 |
001 | A 002 990 43 03 |
| 150 | NUT EXHAUST PIPE TO SUPPORT M8 |
002 | N 000000 003175 |
| 180 | PROFILE CLAMP F EXHAUST FRONT EXHAUST PIPE TO REAR EXHAUST PIPE FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. ADAPT WIRING HARNESS FOR ASSEMBLY RIVET IS ONLY VALID FOR MODEL SERIES 222. FOR REPAIR INFORMATION SEE WIS. ADDITIONAL INFORMATION VIA TECHNICAL MARKET SUPPORT. SEE WIS FOR REPAIR INSTRUCTIONS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. Replaced by: A 000 995 34 33 |
001 | A 000 995 21 33 |
| 180 | PROFILE CLAMP F EXHAUST FRONT EXHAUST PIPE TO REAR EXHAUST PIPE IMPORTANT: ALSO ORDER CLUTCH PEDAL COVER |
001 | A 000 995 30 33 |
| 180 | PROFILE CLAMP F EXHAUST FRONT EXHAUST PIPE TO REAR EXHAUST PIPE FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. ADAPT WIRING HARNESS FOR ASSEMBLY RIVET IS ONLY VALID FOR MODEL SERIES 222. FOR REPAIR INFORMATION SEE WIS. ADDITIONAL INFORMATION VIA TECHNICAL MARKET SUPPORT. SEE WIS FOR REPAIR INSTRUCTIONS. ================================================================================================= SOLDER CONNECTOR SLEEVES: TOTAL WIRE CROSS-SECTION: A 001 546 99 41 GREEN 0.7 - 2.4 MM2 A 002 546 00 41 RED 2.0 - 4.0 MM2 A 002 546 01 41 BLUE 3.5 - 8.0 MM2 A 002 546 11 41 YELLOW 7.5 - 12.0 MM2 BUTT JOINT: A 002 546 13 41 0.5 MM2 A 002 546 14 41 0.8 MM2 A 002 546 15 41 1.3 MM2 A 002 546 16 41 2.0 MM2 =================================================================================================== FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. |
001 | A 000 995 34 33 |
| 200 | EXHAUST SYSTEM CENTRAL Replaced by: A 176 490 63 81 |
001 | A 246 490 24 81 |
| 200 | EXHAUST SYSTEM CENTRAL Replaced by: A 176 490 63 81 |
001 | A 246 490 24 81 |
| 200 | EXHAUST SYSTEM CENTRAL |
001 | A 176 490 63 81 |
| 200 | EXHAUST SYSTEM CENTRAL |
001 | A 176 490 63 81 |
| 210 | PIPE CLAMP F EXHAUST SYS. FRONT EXHAUST PIPE TO REAR EXHAUST PIPE Ø 55 MM |
001 | A 000 995 46 02 |
| 220 | BRACKET FRONT EXHAUST PIPE SUSPENSION |
001 | A 246 490 00 40 |
| 300 | EXHAUST SYSTEM REAR |
001 | A 246 490 25 81 |
| 300 | EXHAUST SYSTEM REAR |
001 | A 246 490 40 81 |
| 300 | EXHAUST GAS LINE RR REAR |
001 | A 246 490 08 00 |
| 300 | EXHAUST SYSTEM REAR |
001 | A 156 490 03 81 |
| 310 | TAIL PIPE COVER LEFT |
001 | A 246 490 02 27 |
| 310 | TAIL PIPE COVER RIGHT |
001 | A 246 490 00 27 |
| 320 | MOUNTING MATERIAL EXHAUST TIP AT LEFT |
001 | A 000 490 00 27 |
| 320 | MOUNTING MATERIAL EXHAUST TIP AT RIGHT |
001 | A 000 490 00 27 |
| 340 | BRACKET REAR |
002 | A 246 492 09 41 |
| 340 | BRACKET CENTRAL EXHAUST SYSTEM |
001 | A 246 492 04 41 |
| 350 | HEXALOBULAR BOLT EXHAUST SYSTEM TO BODY M8X16 |
003 | N 000000 003853 |
| 360 | SUSPENSION F EXHAUST LINE REAR EXHAUST SYSTEM |
002 | A 231 492 00 44 |
| 360 | SUSPENSION RING CENTRAL EXHAUST SYSTEM |
001 | A 168 492 01 44 |
| 400 | LAMBDA PROBE | 001 | A 009 542 56 18 |
| 400 | LAMBDA PROBE DOWNSTREAM CATALYTIC CONVERTER |
001 | A 007 542 63 18 |
| 400 | LAMBDA PROBE CONTROL PROBE IN FRONT OF CATALYST |
001 | A 009 542 56 18 |
| 410 | SPRING CLAMP FOR SENSOR CONNECTOR 28X24 MM |
001 | A 000 991 01 70 |
| 420 | CABLE CLAMP SENSOR LINE FASTENING |
001 | A 000 995 42 68 |
| 430 | TEMPERATURE SENSOR UPSTREAM CATALYTIC CONVERTER WHEN ORDERING, ENSURE FORM IS COMPLETED FULLY AND KEPT ON FILE."SPARE-KEY/LOCKING LUG PART ORDERS". IN THE EVENT OF CRIMINAL INVESTIGATION DOCUMENTARY EVIDENCE MUST BE FURNISHED AT ANY GIVEN TIME. WITH DAS4, USE XENTRY DIAGNOSTICS FOR PROGRAMMING THE DAS4 ADDITIONAL/REPLACEMENT KEY BY SELECTING "PROGRAM AND TEACH IN ADDIT IONAL KEY " OR " PROGRAM AND TEACH IN REPLACEMENT KEY". IMPORTANT: WHEN ORDERING, CITE ADDITIONAL KEY ES-2: 0041. |
001 | A 000 905 57 02 |
| 430 | TEMPERATURE SENSOR UPSTREAM CATALYTIC CONVERTER CAUTION! WHEN ORDERING AUXILIARY KEY ES-2 MUST BE QUOTED READ OUT DATA FROM VEHICLE. WITH DAS4, MAKE SURE TO PERFORM THE FOLLOWING COMMAND WITH XENTRY DIAGNOSTICS PRIOR TO ORDERING: "REGISTER VEHICLE FOR ORDERIN G A PROGRAMMED KEY" |
001 | A 000 905 85 05 |
| 430 | TEMPERATURE SENSOR UPSTREAM CATALYTIC CONVERTER CAUTION! WHEN ORDERING AUXILIARY KEY ES-2 MUST BE QUOTED READ OUT DATA FROM VEHICLE. WITH DAS4, MAKE SURE TO PERFORM THE FOLLOWING COMMAND WITH XENTRY DIAGNOSTICS PRIOR TO ORDERING: "REGISTER VEHICLE FOR ORDERIN G A PROGRAMMED KEY" |
001 | A 000 905 95 05 |
| 435 | LINE FASTENER SENSOR CABLE |
001 | A 003 995 91 77 |
| 440 | CLIP TEMPERATURE SENSOR 18.0X18.5 MM |
001 | A 000 546 20 75 |
| 450 | NOX SENSOR L=815MM OBSERVE SERVICE INFORMATION IN WIS: SI33.30-P-0004A |
001 | A 000 905 71 00 |
| 450 | NOX SENSOR L=815MM FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. NO LONGER AVAILABLE; ORDER NEXT HIGHER ASSEMBLY ====================================================================================I I WORKSHOP KEY ORDER FBS3 I I ============================================I=============================I=========I I I I USE I I ES2 I I I I ============================================I=============================I=========I I I I BLOCK KEY TRACK I USING WORKSHOP KEY I NO.0100 I I I I RELEASE KEY TRACK I USING WORKSHOP KEY I NO.0101 I I I I PERSONALIZE REPLACEMENT EZS BE SURE TO I I I I I I SPECIFY THE FIRST 16 DIGITS OF THE SERIAL I I I I I I NUMBER FROM NEW EZS I USING WORKSHOP KEY I NO.0102 I I I I ACTIVATE REPLACEMENT EIS I USING WORKSHOP KEY I NO.0103 I I I I REMOVE REPLACEMENT ELV TRANSP. PROTECTION I USING WORKSHOP KEY I NO.0104 I I I I PERSONALIZE REPLACEMENT ELV I USING WORKSHOP KEY I NO.0105 I I I I ACTIVATE REPLACEMENT ELV I USING WORKSHOP KEY I NO.0106 I I I I EIS DISGNOSIS I USING WORKSHOP KEY I NO.0107 I I I I ELV ELEC. STG. COLUMN ADJUSTMENT DIAGNOSIS I USING WORKSHOP CODE I NO.0108 I I I I KEY TRACK CONDITION IN VEHICLE I I I I DISPLAY I USING WORKSHOP KEY I NO.0109 I I LAST KEY USED I USING WORKSHOP KEY I NO.0110 I I KEY UTILIZATION VERIFICATION. I BY MEANS OF WORKSHOP KEY... I NO.0111 I I I I ====================================================================================I Replaced by: A 000 905 63 04 |
001 | A 000 905 36 03 |
| 450 | NOX SENSOR FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. NO LONGER AVAILABLE; ORDER NEXT HIGHER ASSEMBLY |
001 | A 000 905 63 04 |
| 470 | BRACKET SENSOR CABLE |
001 | A 168 546 13 43 |
| 480 | CLAMP SENSOR LINE FASTENING 6.5X12.8 MM |
001 | A 000 995 60 44 |
| 490 | DOWEL FASTENING, NOX CONTROL UNIT |
002 | A 000 998 49 85 |
| 495 | PAN HEAD SCREW FASTENING, NOX CONTROL UNIT 4X20 |
002 | N 000000 004679 |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy