Wiring set for engine.
| № | Name | Ext. inf. | A* | Use of | Part number | A |
|---|---|---|---|---|---|---|
| wiring set for engine petr. engine
|
petr. engine | |||||
| wiring set for engine PR-TV0
|
PR-TV0 | |||||
| 1 | wiring set for engine | 1 | 03H 971 627 F | - | ||
| individual parts PR-TV0
|
PR-TV0 | |||||
| - | * corrug. tubes, t-pieces, * clips, holders, grommets, * cable ties, insulating * hose, wiring, * single wires and seals * see special catalogue: * electrical * connecting elements |
|||||
| 2 | flat contact housing with contact locking mechanism control unit use if required: |
1 X X |
5Q0 906 379 A | - | ||
| - | sealing pin | X | 7L0 971 904 | - | ||
| - | sealing pin | X | 7L0 971 904 A | - | ||
| 3 | cable guide injection valve |
1 | 03H 971 824 L | - | ||
| 6 | bracket protective cover | 3 | 022 971 921 | - | ||
| 7 | bracket protective cover | 3 | 022 971 921 A | - | ||
| 8 | flat connector housing with contact locking mechanism injection valve |
X 6 |
4D0 971 992 | - | ||
| 9 | flat connector housing with contact locking mechanism fuel pump |
1 | 4D0 971 992 A | - | ||
| 10 | flat connector housing with contact locking mechanism pressure sensor |
1 | 4D0 971 993 | - | ||
| 11 | flat contact housing with contact locking mechanism oil pressure switch |
1 | 1J0 973 081 | - | ||
| 12 | flat contact housing with contact locking mechanism throttle valve control element |
1 | 4H0 973 713 | - | ||
| 13 | flat contact housing with contact locking mechanism camshaft adjuster unit knock sensor |
X 2 1 |
8K0 973 702 | - | ||
| 14 | flat contact housing with contact locking mechanism additional coolant pump temperature sensor |
X 1 1 |
8K0 973 702 | - | ||
| 15 | flat contact housing with contact locking mechanism low-pressure sensor impulse sender camshaft |
X 1 2 |
8K0 973 703 | - | ||
| 16 | flat contact housing with contact locking mechanism knock sensor |
1 | 8K0 973 703 F | - | ||
| 17 | flat contact housing with contact locking mechanism vent hose |
1 | 1J0 973 722 A | 5 | ||
| 18 | flat contact housing with contact locking mechanism activated charcoal container with valve |
1 | 6X0 973 722 G | - | ||
| 19 | flat contact housing with gasket impulse sender crankshaft |
1 | 1J0 973 723 | - | ||
| 20 | flat contact housing with contact locking mechanism ignition coil |
6 | 4B0 973 724 | 1 | ||
| 21 | flat contact housing with contact locking mechanism central wiring set |
1 | 5Q0 973 837 | - | ||
| 22 | cable tie with terminal socket for bridge strength: (clamp base, rotating) |
1 | 3D0 971 838 M | - | ||
| 23 | cable ties toothed quadrant hole/sheet metal thickness: |
X | 3W0 971 838 | 1 | ||
| (23) | cable holder hole/sheet metal thickness: |
X | 4B0 971 848 | - | ||
| 24 | holder for wiring harness | X | N 104 828 01 | - | ||
| 25 | bracket | X | N 105 023 01 | - | ||
| 26 | cable ties toothed quadrant |
1 | N 909 377 02 | - | ||
| 27 | bracket for corrugated pipe | 1 | N 906 981 01 | - | ||
| (27) | cable holder | 1 | 03L 971 845 G | - | ||
| single parts whitch are not included with the parts supp- lied with the wiring harness PR-TV0
|
PR-TV0 | |||||
| 30 | cable holder gearbox |
1 | 1H0 971 615 AB | - | ||
| 31 | cable guide - upper part counterpart to: |
1 | 03H 971 797 | - | ||
| 32 | holder for wiring harness oil level sensor use if required: |
1 | 1K0 971 842 H | - | ||
| 33 | retaining bracket gearbox |
1 | 1K0 971 858 AS | - | ||
| 34 | retaining clip area: lambda probe |
1 | 1J0 971 939 K | - | ||
| 35 | hexagon collar nut | 2 | N 015 082 10 | - | ||
| 36 | insulating hose temp. resistant: |
X | N 107 676 01 | - |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy