| №- | Name | A* | Part number |
|---|---|---|---|
| 010 | STARTER BATTERY IN ENGINE COMPARTMENT 12V/80AH ====================================================================================I I WORKSHOP KEY ORDER FBS4 I I ============================================I=============================I=========I I I I USE I I ES2 I I I I ============================================I=============================I=========I I I I BLOCK KEY TRACK I USING WORKSHOP KEY I NO.0100 I I I I RELEASE KEY TRACK I USING WORKSHOP KEY I NO.0101 I I I I PERSONALIZE REPLACEMENT EZS BE SURE TO I I I I I I SPECIFY THE FIRST 16 DIGITS OF THE SERIAL I I I I I I NUMBER FROM NEW EZS I USING WORKSHOP KEY I NO.0102 I I I I PERSONALIZE REPLACEMENT ELV I USING WORKSHOP KEY I NO.0105 I I I I PERSONALIZE REPLACEMENT MSG/ECM I USING WORKSHOP KEY I NO.0120 I I I I PERSONALIZE REPLACEMENT VGS/TCM I USING WORKSHOP KEY I NO.0121 I I I I PERSONALIZE REPLACEMENT ISM/DSM I USING WORKSHOP KEY I NO.0122 I I I I PERSONALIZE REPLACEMENT LEE/EM2 I USING WORKSHOP KEY I NO.0123 I I I I PERSONALIZE REPLACEMENT EMSG/EMCU I USING WORKSHOP KEY I NO.0124 I I I I REPORT VEHICLE AS ABSENT I USING WORKSHOP KEY I NO.0125 I I I I ====================================================================================I |
001 | A 001 982 81 08 |
| 010 | STARTER BATTERY IN ENGINE COMPARTMENT 12V/78AH WITH DAS4, MAKE SURE TO PERFORM THE FOLLOWING COMMAND WITH XENTRY DIAGNOSTICS PRIOR TO ORDERING: "REGISTER VEHICLE FOR ORDERIN G A PROGRAMMED KEY" ALSO ORDER: TERMINAL BLOCK 2 X A 001 546 99 41; CABLE TIE 5 X A 002 997 24 90 PART MUST BE CHECKED AFTER INSTALLATION FOR CURRENT FLASHWARE Replaced by: A 000 982 53 03 |
001 | A 002 982 06 08 |
| 010 | STARTER BATTERY IN ENGINE COMPARTMENT PART MUST BE CHECKED AFTER INSTALLATION FOR CURRENT FLASHWARE |
001 | A 000 982 53 03 |
| 030 | STOP PLUG ON BATTERY,LATERALLY 6X8 MM |
001 | A 002 997 24 86 |
| 030 | STOP PLUG ON BATTERY,LATERALLY 6X8 MM |
001 | A 002 997 24 86 |
| 035 | BLEED HOSE BATTERY VENTING WITH DAS4, MAKE SURE TO PERFORM THE FOLLOWING COMMAND WITH XENTRY DIAGNOSTICS PRIOR TO ORDERING: "REGISTER VEHICLE FOR ORDERIN G A PROGRAMMED KEY" POSITIVE CHANGE IN CASTER ( + 3 MM ) Replaced by: A 011 997 01 52 |
001 | A 009 997 16 52 |
| 035 | BLEED HOSE BATTERY VENTING |
001 | A 011 997 01 52 |
| 040 | ELBOW FITTING ON BATTERY,LATERALLY |
001 | A 000 990 38 72 |
| 040 | ELBOW FITTING ON BATTERY,LATERALLY |
001 | A 000 990 38 72 |
| 050 | HOSE BATTERY VENTING 5 X 1 MM ORDER BY THE METER |
NB | A 024 997 49 82 |
| 050 | HOSE BATTERY VENTING 5 X 1 MM ORDER BY THE METER |
NB | A 024 997 49 82 |
| 060 | PLUG LEGROOM DRIVER'S SEAT SIDE 11 MM |
001 | A 000 998 18 50 |
| 060 | PLUG LEGROOM CO-DRIVER'S SEAT SIDE 11 MM |
001 | A 000 998 18 50 |
| 060 | BUTTON GROMMET FOR HOSE WITH BATTERY LOCATED IN REAR END |
001 | A 000 998 02 01 |
| 090 | CURRENT LIMITER | 001 | A 000 906 15 05 |
| 090 | CURRENT LIMITER | 001 | A 000 906 15 05 |
| 100 | BATTERY SENSOR NEGATIVE LINE WITH BATTERY SENSOR |
001 | A 000 905 65 07 |
| 100 | BATTERY SENSOR NEGATIVE LINE WITH BATTERY SENSOR |
001 | A 000 905 05 54 |
| 120 | ELECTRICAL WIRING HARNESS FROM TRANSMISSION TO BODY |
001 | A 205 540 85 18 |
| 140 | ELECTRICAL WIRING HARNESS CONNECTING POINT TO STARTER AND ALTERNATOR |
001 | A 205 540 35 12 |
| 185 | HEXALOBULAR BOLT FOR STARTER AND GENERATOR WIRING HARNESS M6X12 |
001 | N 910143 006000 |
| 240 | HEXAGON NUT FASTENING WIRING HARNESS CIRCUIT 50 TO STARTER M6 |
001 | N 910112 006001 |
| 240 | NUT WIRING HARNESS MOUNTING, CIRCUIT 30 TO STARTER M8 |
001 | A 000 548 04 72 |
| 245 | PROTECTIVE CAP PROTECTION AGAINST ACCIDENTAL CONTACTFOR CIRCUIT 30, STARTER |
001 | A 001 546 61 35 |
| 250 | NUT FASTENING WIRING HARNESS CIRCUIT 30 TO GENERATOR M8 |
001 | A 000 548 04 72 |
| 255 | PROTECTIVE CAP CONTACT PROTECTION FOR CIRCUIT 30, ALTERNATOR |
001 | A 001 546 61 35 |
| 335 | BOLT FASTENING, BUSBAR 6X12 |
004 | A 001 984 67 29 |
| 340 | NUT ALTERNATOR WIRING HARNESS TO BUSBAR M8 |
001 | N 000000 003175 |
| 340 | NUT STARTER WIRING HARNESS TO BUSBAR M8 |
001 | N 000000 003175 |
| 350 | BUSBAR CAP | 002 | A 205 545 07 00 |
| 360 | BUSBAR CAP LATERAL LEFT |
001 | A 205 545 11 00 |
| 365 | BUSBAR CAP LATERAL RIGHT |
001 | A 205 545 10 00 |
| 370 | BUSBAR CAP LEFT |
001 | A 205 545 18 00 |
| 375 | BUSBAR CAP RIGHT |
001 | A 205 545 18 00 |
| 380 | FEED-THROUGH GROMMET (BLINDTUELLE) |
001 | A 002 998 00 01 |
| 390 | NUT SPECIAL SHAPE JUMP START NEGATIVE TERMINAL |
001 | A 001 990 85 52 |
| 420 | ELECTRICAL WIRING HARNESS CONNECTING POINT TO PREFUSE BOX AND CONTROL UNIT X244/5 TO F32/3*13; X244/1 TO N16/2 |
001 | A 205 540 52 03 |
| 430 | NUT WIRING HARNESS TO BUSBAR, CONNECTION: X244/5; X244/6 |
001 | N 913025 008000 |
| 430 | NUT WIRING HARNESS TO BUSBAR, CONNECTION: X244/1; X244/2 |
001 | N 913025 008000 |
| 440 | NUT FASTENING, ELECTRICAL LINE TO CURRENT LIMITER N16/2 TO X244/1 |
001 | N 913025 008000 |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy