| №- | Name | A* | Part number |
|---|---|---|---|
| 010 | STARTER BATTERY IN ENGINE COMPARTMENT 12V/78AH PART MUST BE CHECKED AFTER INSTALLATION FOR CURRENT FLASHWARE |
001 | A 002 982 06 08 |
| 010 | STARTER BATTERY IN ENGINE COMPARTMENT 12V/78AH FIRST EXHAUST STOCK OF OLD PARTS UP TO IDENT NO. WITH DAS4, USE XENTRY DIAGNOSTICS FOR PROGRAMMING THE DAS4 ADDITIONAL/REPLACEMENT KEY BY SELECTING "PROGRAM AND TEACH IN ADDIT IONAL KEY " OR " PROGRAM AND TEACH IN REPLACEMENT KEY". PART MUST BE CHECKED AFTER INSTALLATION FOR CURRENT FLASHWARE Replaced by: A 000 982 53 03 |
001 | A 002 982 06 08 |
| 010 | STARTER BATTERY IN ENGINE COMPARTMENT PART MUST BE CHECKED AFTER INSTALLATION FOR CURRENT FLASHWARE |
001 | A 000 982 53 03 |
| 010 | BATTERY IN ENGINE COMPARTMENT 12V/70 AH |
001 | A 004 541 86 01 |
| 010 | STARTER BATTERY IN ENGINE COMPARTMENT 12V/80AH IMPORTANT! NOTE MANUFACTURER OF REMOVED PART |
001 | A 000 982 21 08 |
| 010 | STARTER BATTERY IN ENGINE COMPARTMENT 12V/80AH WITH DAS4, MAKE SURE TO PERFORM THE FOLLOWING COMMAND WITH XENTRY DIAGNOSTICS PRIOR TO ORDERING: "REGISTER VEHICLE FOR ORDERIN G A PROGRAMMED KEY" |
001 | A 001 982 81 08 |
| 015 | PROTECTIVE CAP POLE COVER CAP |
001 | A 001 546 08 35 |
| 015 | INSULATING CAP POLE COVER CAP |
001 | A 000 546 85 02 |
| 030 | STOP PLUG ON BATTERY,LATERALLY 6X8 MM |
001 | A 002 997 24 86 |
| 030 | STOP PLUG ON BATTERY,LATERALLY 6X8 MM |
001 | A 002 997 24 86 |
| 035 | BLEED HOSE BATTERY VENTING |
001 | A 009 997 16 52 |
| 040 | ELBOW FITTING ON BATTERY,LATERALLY |
001 | A 000 990 38 72 |
| 040 | ELBOW FITTING ON BATTERY,LATERALLY |
001 | A 000 990 38 72 |
| 050 | HOSE BATTERY VENTING 5 X 1 MM ORDER BY THE METER |
NB | A 024 997 49 82 |
| 050 | HOSE BATTERY VENTING 5 X 1 MM ORDER BY THE METER |
NB | A 024 997 49 82 |
| 060 | PLUG LEGROOM DRIVER'S SEAT SIDE 11 MM |
001 | A 000 998 18 50 |
| 060 | PLUG LEGROOM CO-DRIVER'S SEAT SIDE 11 MM |
001 | A 000 998 18 50 |
| 060 | PLUG PLUG FOR VENTILATION HOLES 11 MM;SCR |
001 | A 000 998 18 50 |
| 060 | BUTTON GROMMET FOR HOSE WITH BATTERY LOCATED IN REAR END |
001 | A 000 998 02 01 |
| 090 | CURRENT LIMITER | 001 | A 000 906 87 05 |
| 090 | CURRENT LIMITER | 001 | A 000 906 15 05 |
| 095 | INSULATING CAP CURRENT LIMITER |
001 | A 002 546 37 35 |
| 100 | BATTERY SENSOR NEGATIVE LINE WITH BATTERY SENSOR |
001 | A 000 905 05 54 |
| 100 | BATTERY SENSOR NEGATIVE LINE WITH BATTERY SENSOR ATTENTION: ORDER WASHER AS WELL |
001 | A 000 905 60 01 |
| 100 | BATTERY SENSOR NEGATIVE LINE WITH BATTERY SENSOR |
001 | A 000 905 65 07 |
| 100 | BATTERY SENSOR NEGATIVE LINE WITH BATTERY SENSOR |
001 | A 000 905 30 06 |
| 120 | ELECTRICAL WIRING HARNESS FROM TRANSMISSION TO BODY |
001 | A 205 540 77 16 |
| 120 | ELECTRICAL WIRING HARNESS FROM TRANSMISSION TO BODY |
001 | A 205 540 79 16 |
| 140 | ELECTRICAL WIRING HARNESS CONNECTING POINT TO STARTER AND ALTERNATOR |
001 | A 205 540 55 03 |
| 140 | ELECTRICAL WIRING HARNESS CONNECTING POINT TO STARTER AND ALTERNATOR |
001 | A 253 540 07 01 |
| 140 | ELECTRICAL WIRING HARNESS CONNECTING POINT TO STARTER AND ALTERNATOR |
001 | A 253 540 53 04 |
| 185 | HEXALOBULAR BOLT ALTERNATOR WIRING HARNESS AT ENGINE SUPPORT M8X20 Replaced by: N 000000 000276 |
001 | N 910142 008000 |
| 185 | HEXALOBULAR BOLT ALTERNATOR WIRING HARNESS AT ENGINE SUPPORT M8X20 |
001 | N 000000 000276 |
| 240 | HEXAGON NUT FASTENING WIRING HARNESS CIRCUIT 50 TO STARTER M6 |
001 | N 910112 006001 |
| 240 | NUT WIRING HARNESS MOUNTING, CIRCUIT 30 TO STARTER M8 |
001 | A 000 548 04 72 |
| 245 | PROTECTIVE CAP PROTECTION AGAINST ACCIDENTAL CONTACTFOR CIRCUIT 30, STARTER |
001 | A 001 546 61 35 |
| 250 | NUT FASTENING WIRING HARNESS CIRCUIT 30 TO GENERATOR M8 |
001 | A 000 548 04 72 |
| 255 | PROTECTIVE CAP CONTACT PROTECTION FOR CIRCUIT 30, ALTERNATOR |
001 | A 001 546 61 35 |
| 330 | BUSBAR | 001 | A 205 545 15 00 |
| 330 | BUSBAR |
001 | A 205 545 16 00 |
| 330 | BUSBAR ALSO ORDER: TERMINAL BLOCK 2 X A 001 546 99 41; CABLE TIE 5 X A 002 997 24 90 |
001 | A 205 545 51 00 |
| 335 | BOLT FASTENING, BUSBAR 6X12 |
004 | A 001 984 67 29 |
| 340 | NUT ALTERNATOR WIRING HARNESS TO BUSBAR M8 |
001 | N 000000 003175 |
| 340 | NUT STARTER WIRING HARNESS TO BUSBAR M8 |
001 | N 000000 003175 |
| 345 | BUSBAR CAP | 001 | A 205 545 06 00 |
| 350 | BUSBAR CAP | 001 | A 205 545 82 00 |
| 350 | BUSBAR CAP | 001 | A 205 545 07 00 |
| 360 | BUSBAR CAP LATERAL LEFT |
001 | A 205 545 11 00 |
| 370 | BUSBAR CAP LEFT |
001 | A 205 545 18 00 |
| 380 | FEED-THROUGH GROMMET (BLINDTUELLE) |
001 | A 002 998 00 01 |
| 390 | NUT SPECIAL SHAPE JUMP START NEGATIVE TERMINAL |
001 | A 001 990 85 52 |
| 420 | ELECTRICAL WIRING HARNESS CONNECTING POINT TO PREFUSE BOX AND CONTROL UNIT F32/3 TO X244/5; N16/2 TO X244/1 |
001 | A 205 540 52 03 |
| 430 | NUT WIRING HARNESS TO BUSBAR, CONNECTION: X244/5; X244/6 |
001 | N 913025 008000 |
| 430 | NUT WIRING HARNESS TO BUSBAR, CONNECTION: X244/1; X244/2 |
001 | N 913025 008000 |
| 440 | NUT FASTENING, ELECTRICAL LINE TO CURRENT LIMITER N16/2 TO X244/1 |
001 | N 913025 008000 |
Copyright © 2024 WebAutoCats.com. All rights reserved. Terms of Use | Privacy Policy